Turning & Specialty Stair Calculators

Seven calculators for stairs that do not run straight: quarter-turn and half-turn stairs with landings, winder treads, spiral and curved stairs, ship ladders and alternating tread stairs for lofts, and pull-down attic ladders. Each lays out the stair, draws it to scale and checks the rules that apply to that type — walkline depths, clear width, headroom, angle and landing space.

By the Stair-Math TeamUpdated

The 7 turning and specialty stair calculators

Which turning or specialty stair calculator do you need?

Pick the calculator by the stair you are planning
Your stairCalculatorWhat you get
Turns 90° along two wallsL-shaped stair calculatorRisers per flight, landing height, the length of each leg and each stringer — from the rise or to fit two walls
Turns 180° and comes backU-shaped stair calculatorTwo flights, the half landing, the stairwell size and the gap between flights
Turns with tapered treads instead of a landingWinder stair calculatorWinder depths at the walkline and the narrow end, checked against the code — or a check of winders you already have
Climbs round a centre poleSpiral staircase calculatorTreads, rotation, walkline depth, clear width, headroom and the floor opening — by diameter or by opening
Sweeps on a large radius, open in the middleCurved staircase calculatorTread depths at the inside, walkline and outside, and the inner and outer stringer lengths
Steep stair to a small loftShip ladder calculatorRiser, tread and floor length at your angle, for a ship ladder or an alternating tread stair
Folds down from a ceiling hatchAttic ladder calculatorWhether a kit fits your opening and ceiling height, its angle, landing space and weight rating

For a straight stair, start with the stair layout calculators; every turning stair here still begins with the same total rise.

How much space each stair type needs

One 108 in (9 ft) climb, 36 in wide, 7.2 in risers and 10½ in treads (IRC)
Stair typeOutlineFloor covered
Spiral, 60 in diameter60 × 60 in25.0 ft²
Straight148 × 36 in37.0 ft²
L-shaped with winders100 × 88.5 in38.1 ft²
Straight with a mid landing173.5 × 36 in43.4 ft²
L-shaped with a landing110.5 × 99 in43.4 ft²
U-shaped with a half landing110.5 × 74 in52.9 ft²

The outline is the rectangle the stair needs; the floor covered is what the treads and landings actually sit on — an L leaves the inside corner free. A ship ladder at 60° for the same rise needs only about 66 × 24 in. Compare layouts for your own rise with the staircase footprint calculator.

Which stairs the code allows, and where

US IRC rules for each stair type
Stair typeWhere it may be usedKey limits
L and U with landingsAny stairSame riser and tread limits as a straight stair; landings at least as deep as the stair is wide and 36 in minimum
WindersAny stairAt least 10 in deep at the walkline (12 in from the narrow side) and 6 in at any point; walkline depths within 3/8 in
SpiralAny stair in a home26 in clear width; 6¾ in tread at the walkline; risers up to 9½ in; 6 ft 6 in headroom; all treads identical
CurvedAny stairTreated as winders: 10 in at the walkline, 6 in minimum; risers up to 7¾ in
Ship ladder / alternating treadA loft or mezzanine of 200 ft² or lessHandrails both sides; ship ladder treads at least 5 in, 8½ in with nosing, risers up to 9½ in
Attic ladderAttic access only — not a stairFollow the maker’s ceiling height range, landing space and load rating

UK Part K and the Australian NCC set their own rules for tapered treads and spiral stairs, and the calculators switch to them when you choose that region. Workplace ship stairs follow OSHA instead.

Choosing a stair type

  • Main stair to bedrooms: straight, L or U. Landings make the turn safe and let a sofa or a mattress go round; winders save a tread depth per turn if the space is tight.
  • Tight footprint, habitable room above: a spiral at 5 ft diameter or more, or a U-shaped stair that folds back on itself.
  • A feature stair in an open hall: a curved stair — but it needs a large radius and long, laminated stringers.
  • A small loft or storage platform: a ship ladder or alternating tread stair at 60–70°, with handrails on both sides.
  • An attic you visit a few times a year: a pull-down ladder — check the ceiling height range and the landing space before you buy.

Walklines and winders, explained

Any tread that is wider at one end than the other — a winder, a curved-stair tread or a spiral tread — is measured on the walkline, the path people naturally take. The IRC puts it 12 in in from the narrow side of the clear width; a spiral’s walkline sits on a fixed radius from the centre pole. The tread must be deep enough there to feel like a normal step, and still deep enough at the narrow end for a foot.

That is why a 90° turn usually takes three winders of 30°: with four, each turns only 22½° and comes out under 10 in at the walkline on a house stair; with two, each one is a long, steep wedge that is awkward to walk. On a 36 in stair with 10½ in treads, three 30° winders measure 12.23 in at the walkline and 6.02 in at the narrow end — both over the IRC minimums of 10 in and 6 in. The winder stair calculator works out the inside radius that makes them pass.

Turning and specialty stair FAQs

What type of stair takes the least space?

For a 9 ft climb, a 60 in spiral uses about 25 ft² of floor, a straight stair about 37 ft², an L-shaped stair with winders about 38 ft² and an L or U with landings 43–53 ft². A ship ladder takes even less — about 11 ft² — but it only serves a small loft, not a bedroom floor.

Do turning stairs need a landing?

Not always. A quarter turn or half turn can use a landing or winder treads. A landing is safer and easier for furniture; winders save about one tread depth of wall per turn but have narrow inside ends and must meet the walkline rules. Long straight runs need a landing anyway once the flight rises more than 151 in under the IRC.

Are winder stairs, spiral stairs and ship ladders allowed in homes?

Under the IRC, winders and spiral stairs are permitted stair types in a home when they meet their own rules. A ship ladder is allowed only to a small loft or mezzanine, not as the stair to bedrooms or an exit route. An attic ladder is access to an attic, not a stair. Local amendments can be stricter.

What is the difference between an L-shaped and a U-shaped stair?

An L-shaped (quarter-turn) stair turns 90° once, so it fits along two walls. A U-shaped (half-turn) stair turns 180°, so both flights sit side by side and the stair finishes above where it started — it needs a wider but shorter space.

Which specialty stair is best for a loft?

A spiral stair if the loft is a habitable room and you have about 5 ft of floor; a ship ladder or alternating tread stair if the loft is small storage or a sleeping platform up to 200 ft²; a pull-down attic ladder if the space above is only an attic. Moving furniture is hardest on a ship ladder and easiest on a conventional stair.

Can I turn a straight stair into an L or U stair?

Yes — the riser height stays the same, because it comes from the total rise. A landing takes one riser’s place in the count and adds a platform at least as deep as the stair is wide; winders replace the landing with tapered treads. The L-shaped and U-shaped calculators show how the risers split between the flights.

Sources

  1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Width (R311.7.1), headroom (R311.7.2), 151 in flight limit (R311.7.3), walkline (R311.7.4), winders (R311.7.5.2.1), landings at least as deep as the stair is wide and not less than 36 in (R311.7.6), handrails on flights of four or more risers (R311.7.8) and spiral stairs (R311.7.10.1).
  2. Approved Document K: Protection from falling, collision and impact (opens in a new tab)UK Government (statutory guidance for England). Maximum riser, maximum pitch and 2R + G range.
  3. National Construction Code 2019, Volume Two, Part 3.9.1 — Stair construction (opens in a new tab)Australian Building Codes Board. Riser and going limits and 2R + G range (Table 3.9.1.1), no more than 18 and no fewer than 2 risers in each flight.
  4. Occupational Safety and Health Administration, 29 CFR 1910.25 — Stairways (opens in a new tab)US Department of Labor. Ship stairs in workplaces: 50–70° from horizontal, risers 6½–12 in, treads at least 4 in deep, at least 18 in wide.

Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

All calculatorsEvery Stair-Math calculator on one page, by category.View all

Other stair calculator categories