U-Shaped Stair Calculator

Enter your floor-to-floor height, flight width and well gap and get a complete U-shaped (switchback) stair: risers in each flight, the half landing and its height, and the stairwell length and width. Or enter the stairwell you have and the calculator works out the flight width and a riser count that fits.

By the Stair-Math TeamUpdated How we check this calculator

What do you know?

Your stair

in

Finished floor to finished floor. Not sure? Work out your total rise.

in

The riser count is rounded to fit your rise exactly.

in

Riser face to riser face, not counting the nosing.

in

Each flight. 36 in is the IRC minimum, 44 in typical under the IBC.

in

0 = dogleg (flights side by side); wider = open-well stair.

Landing position
Quick picks:

Top step
Units

Your U-shaped stair

The U-shaped stair in plan, drawn to scale, with the stairwell length and width
Plan view to scale: lower flight, half landing across both flights, upper flight coming back. Drag the well edge to change the gap; in Fit to stairwell, drag the stairwell sides.

U-stair check

    Solved with your numbers

      Assumptions: both flights the same width; the half landing runs across both flights and the well; equal risers; the nosing counted once, at the bottom of the lower flight. Stairwell sizes are to the face of the finished stair — wall finishes are not included.

      Width, landing depth, riser and flight limits from the IRC (R311.7), the IBC (1011) and the codes listed under Sources; layouts follow from the geometry on this page. Tested against 6 worked cases, including a metric dogleg, a 160 in rise and stairwells too narrow and too short. See the method · Sources

      How to calculate a U-shaped stair

      A U-shaped stair climbs one flight, turns 180° on a half landing and climbs a second flight back alongside the first. The risers come from the whole rise, exactly as in the stair calculator; the landing is the top tread of the lower flight.

      With n risers of height R, tread depth T, nosing N, flight width W, well gap g and landing depth Ld:

      lower flight: n1 = ceil(n ÷ 2) risers (or your choice), length L1 = (n1 − 1) × T + N

      upper flight: n2 = n − n1 risers, length L2 = (n2 − 1) × T (n2 × T with a flush top tread)

      stairwell length = max(L1, L2) + Ld · stairwell width = 2W + g

      landing height = n1 × R · half landing = Ld × (2W + g)

      stringer = √((flight risers × R)² + flight run²) · bounding area = length × width

      In Fit to stairwell, the flight width comes from the stairwell: W = (available width − g) ÷ 2. The calculator then tries every riser count your code allows, closest to your target riser first, and takes the first whose stairwell length fits. If the even split is a little too long and the stair has an odd number of risers, it also tries putting the extra riser in the upper flight, which saves the nosing on the longer flight.

      Worked examples

      A 9 ft U-stair from the total rise

      1. Inputs108 in rise · 7¼ in target riser · 10½ in treads · 1 in nosing · 36 in flights · 36 in landing · 4 in well · even split · IRC.
      2. Risers15 of 7.20 in (7-3/16"); lower flight 8 risers and 7 treads (73.50 in run), upper flight 7 risers and 6 treads (63.00 in).
      3. Stairwell lengthmax(73.5 + 1, 63) + 36 = 110.50 in (9' 2-1/2").
      4. Stairwell width2 × 36 + 4 = 76 in (6' 4"); half landing 36 × 76 in, its top 57.60 in up.
      5. Area and stringers110.5 × 76 = 58.32 ft²; stringers 93.38 in and 80.68 in.

      Fitting a 120 × 78 in stairwell

      1. Flight width(78 − 4) ÷ 2 = 37 in, just over the 36 in IRC minimum; the landing defaults to 37 in.
      2. Length15 risers give max(74.5, 63) + 37 = 111.50 in — inside the 120 in, with 8.50 in spare.

      Shrink the stairwell to 95 in long and nothing fits: even 14 risers at 7.71 in need 64 + 37 = 101 in, 6 in too long. In a 70 in wide stairwell the flights would be only 33 in — two 36 in flights and a 4 in well need 76 in.

      How much space does a U-shaped stair need?

      Stairwell size for a U-stair with an even split (7¼ in target riser, 10½ in treads, 1 in nosing, landing = flight width, IRC)
      Floor to floorRisers36 in flights, 4 in well36 in flights, no well42 in flights, 4 in well
      8 ft (96 in)13 × 7-3/8"8' 4" × 6' 4"8' 4" × 6' 0"8' 10" × 7' 4"
      9 ft (108 in)15 × 7-3/16"9' 2-1/2" × 6' 4"9' 2-1/2" × 6' 0"9' 8-1/2" × 7' 4"
      10 ft (120 in)17 × 7-1/16"10' 1" × 6' 4"10' 1" × 6' 0"10' 7" × 7' 4"

      The width does not change with the rise — only the length does, about 10½ in for every two extra risers. Add wall finishes on the outside, and use the stairwell opening calculator for headroom where the upper flight passes over the lower one.

      Half landing size

      On a U-stair the landing carries you through a full 180° turn, so it must run the whole width — both flights plus the well — and be at least as deep as one flight is wide (IRC R311.7.6, and not less than 36 in). Two 36 in flights with a 4 in well need at least 36 × 76 in. A square 48 × 48 in landing, sometimes quoted for U-stairs, does not reach across both flights.

      The landing height is the top of the finished landing above the lower finished floor — take off its floor finish for the framing. For moving furniture, a landing 42–48 in deep makes the turn much easier; the calculator flags anything under 42 in.

      Dogleg vs open-well stairs

      Well gap and what it changes
      Well gapTypeGood forWatch out for
      0DoglegThe narrowest U; flights share a central wall or newelHandrails must break at the newel; less light
      2–6 inNarrow wellRoom for a continuous inside handrailGap must not let a child through between guards
      12 in or moreOpen wellLight down the stair, a feature stairGuards needed along the well edge

      Every inch of well gap adds an inch to the stairwell width; it does not change the length. The table under your result shows the stairwell for five gaps.

      U-shaped vs L-shaped stairs

      For a 9 ft rise and a 36 in stair, a U needs about 110½ × 76 in and an L with a square landing about 110½ × 99 in, though the L leaves its inside corner free. The U ends where it began, which suits a central core and keeps the opening above short; the L turns a corner and suits a room edge. If a 180° turn will not fit, try the L-shaped stair calculator, or replace the half landing with winders using the winder stair calculator. To see every layout side by side, use the staircase footprint calculator.

      How to read your result

      Result terms and next steps
      TermMeaningNext step
      Stairwell length × widthThe box the stair needs on planFrame the walls to this plus their finishes
      Half landingDepth × full width of the landingFrame it to the landing height less its floor finish
      Flight width (fit mode)What your stairwell leaves for each flightCheck it against the code minimum
      Short byExtra length needed at the best riser countReduce the gap, use winders or a steeper riser within code

      What this calculator does not cover

      • 90° turns and winders: use the L-shaped and winder stair calculators.
      • The opening and headroom above: use the stairwell opening calculator.
      • Handrail length round the turn, stringer cuts and materials — each has its own calculator.

      U-shaped stair FAQs

      How much space does a U-shaped staircase need?

      For a 9 ft rise (108 in) with two 36 in flights, 10½ in treads and a 4 in well, a U-stair needs a stairwell about 9 ft 2½ in long × 6 ft 4 in wide. For an 8 ft rise it is about 8 ft 4 in × 6 ft 4 in. The width is always twice the flight width plus the well; the length is the longer flight plus the landing.

      What size is a half landing?

      It runs the full width of the stair — both flights plus the well — and must be at least as deep as one flight is wide. Two 36 in flights with a 4 in well need a half landing at least 36 in deep × 76 in wide. A small square “landing” is not enough on a U-stair, because you turn through 180° on it.

      What is the difference between a dogleg and an open-well stair?

      Both turn 180° at a half landing. In a dogleg the flights sit side by side with no gap (or a thin wall) between them; in an open-well stair there is a well between the flights, often a few inches to a foot. A dogleg is narrower; an open well lets light down and makes room for a continuous handrail.

      How many steps should each flight of a U-stair have?

      Split the risers as evenly as you can: a 15-riser stair is usually 8 below the landing and 7 above. Each flight must stay under the flight limit — 151 in of rise under the IRC, 144 in under the IBC and 18 risers in Australia — and a flight should have at least 2 risers.

      Is a U-shaped or an L-shaped stair better?

      A U-stair is shorter and fits a compact core, with the top and bottom of the stair at the same end. An L-stair is narrower and suits a corner. For the same 9 ft rise and 36 in stair, the U needs about 110½ × 76 in and the L about 110½ × 99 in.

      Can a U-shaped stair use winders instead of a half landing?

      Yes. A 180° turn can be made with winders — usually six, three for each 90° — which shortens the stairwell. Winders must meet walkline rules (10 in at the walkline and 6 in at the narrow end under the IRC), and they are harder to carry furniture round.

      How wide should a U-shaped stairwell be?

      Twice the flight width plus the well gap. Under the IRC each flight must be at least 36 in, so the stairwell is at least 72 in with no gap and 76 in with a 4 in well. Commercial stairs under the IBC are usually 44 in per flight, so 88 in or more.

      Sources

      1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Width (R311.7.1), headroom (R311.7.2), 151 in flight limit (R311.7.3), walkline (R311.7.4), winders (R311.7.5.2.1), landings at least as deep as the stair is wide and not less than 36 in (R311.7.6), handrails on flights of four or more risers (R311.7.8) and spiral stairs (R311.7.10.1).
      2. International Building Code 2021, Chapter 10, Section 1011 — Stairways (opens in a new tab)International Code Council. 44 in typical minimum stair width (1011.2), riser and tread limits and the 144 in flight limit.
      3. National Construction Code 2019, Volume Two, Part 3.9.1 — Stair construction (opens in a new tab)Australian Building Codes Board. Riser and going limits and 2R + G range (Table 3.9.1.1), no more than 18 and no fewer than 2 risers in each flight.
      4. Approved Document K: Protection from falling, collision and impact (opens in a new tab)UK Government (statutory guidance for England). Maximum riser, maximum pitch and 2R + G range.
      5. National Building Code of Canada 2020 (opens in a new tab)National Research Council Canada. 860 mm minimum width for stairs within dwelling units (9.8.2.1) and riser and run limits.
      6. U-stair geometryDerived from geometry: flight lengths, stairwell length and width, landing height and stringer lengths follow from the riser count, tread depth, nosing, flight width, well gap and landing depth.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Turning & specialty stair calculatorsAll 7 tools for stairs that turn, wind or climb steeply — L-shaped, U-shaped, winder, spiral, curved, ship ladder and attic ladder.View all 7

      Other stair calculator categories