Total Rise Calculator

Total rise is the one number every stair depends on. Build it up from your ceiling height, floor framing and flooring to get the finished and rough rise — or, for a deck or porch on sloping ground, find the true rise at the point where the stair actually lands.

By the Stair-Math TeamUpdated How we check this calculator

Where is the stair going?

Your measurements

in

Lower level, finished floor to finished ceiling (an 8 ft ceiling is 96 in).

in

½ in drywall · 5/8 in drywall · 0 for open joists.

Actual depth of the upper floor framing.

in

¾ in plywood or OSB is typical.

in

Carpet + pad ¾ · hardwood ¾ · LVP ¼ · tile + backer ¾.

in

Enter 0 for a bare slab.

Quick picks — typical builds:
Units

Your total rise

Section through the floors, or the deck and sloping ground, drawn to scale with the total rise
Drag the yellow handle to change the ceiling height or the deck height — the rise follows.

Rise check

    Solved with your numbers

      Assumptions: floor layers are flat; ceiling height is measured finished floor to finished ceiling on the lower level; on sloping ground the slope is uniform between the top of the stair and the landing, and the landing pad top is level. All risers must match within 3/8 in, including the top and bottom step after flooring is installed.

      Riser uniformity rule from the IRC (R311.7); layer and slope figures follow from geometry. Tested against 6 worked cases, including mismatched finishes, metric framing, rising ground and a landing pad. See the method · Sources

      How to measure total rise for stairs

      Total rise is the vertical distance from the finished lower floor to the finished upper floor, measured where the stair will stand. It decides the number of risers and the height of every step, so an error here is copied into every step of the stair.

      1. Carry a level line outLay a long level or a straight board on the finished upper floor so it overhangs the opening. Check it is level.
      2. Measure straight downMeasure from the underside of the board to the lower floor at the point where the bottom step will land, not at the wall.
      3. Add the missing finishesIf flooring is not installed yet on either level, add its thickness at the top and at the bottom so you have the finished rise.
      4. Check against the plansBuild the rise up from the drawings with the calculator above. If the measured and planned figures differ by more than ¼ in, find out why before you cut stringers.

      Never drop a tape from the upper floor onto a lower floor that is not level, and never use the ceiling height as the total rise — the floor structure above adds 9 to 18 in.

      How the total rise calculator works

      From floor build-up

      The finished rise is the stack of layers between the two finished floors:

      finished rise = ceiling height + ceiling finish + joist depth + subfloor + upper finish

      rough rise = finished rise + lower finish − upper finish — lower subfloor or slab to upper subfloor

      finish difference = |upper finish − lower finish|

      The ceiling height is measured on the lower level from finished floor to finished ceiling, so the lower flooring is already inside it. The riser preview uses the same rule as the stair calculator at a 7¼ in target.

      From sloped or uneven ground

      When the ground slopes, the bottom of the stair lands one run out from the deck, where the ground is lower (or higher) than under the deck edge. But the run depends on how many risers there are, which depends on the rise. So the calculator repeats:

      slope s = ground change ÷ horizontal distance (negative when the ground rises)

      start: H = deck height − pad

      repeat: n from H (stair calculator rule) → run L = (n − 1) × tread → H = deck height + s × L − pad

      stop when H stops changing (to a millionth of an inch, at most 30 rounds)

      It usually settles in two or three rounds. If the rise sits exactly on the boundary between two riser counts and flips between them, the larger rise is reported with a note.

      Floor build-up from the lower finished floor to the upper finished floor: ceiling height, ceiling finish, joist, subfloor and upper finish upper finishsubfloorjoistsceiling finish ceiling height TOTAL RISE
      Finished total rise runs from the finished lower floor to the finished upper floor: the ceiling height plus every layer of the floor above.

      Worked examples

      A new house with an 8 ft ceiling

      1. InputsCeiling 96 in · ½ in drywall · 11-7/8 in I-joists · ¾ in subfloor · ¾ in hardwood up · ¾ in flooring down.
      2. Finished rise96 + 0.5 + 11.875 + 0.75 + 0.75 = 109.875 in (109-7/8", 9' 1-7/8").
      3. Rough rise109.875 + 0.75 − 0.75 = 109.875 in — the finishes match, so the difference is 0.
      4. Riser preview15 risers of 7.33 in (7-5/16") at a 7¼ in target.

      Change the lower floor to a bare basement slab (0 in) and the finished rise stays 109.875 in, but the rough rise drops to 109.125 in. The finishes now differ by ¾ in — twice the 3/8 in allowed — so stringers laid out from the rough rise would leave a bad top or bottom step.

      A deck stair on ground that falls away

      1. Inputs36 in from the deck surface to the ground at the deck edge · ground falls 3 in over 4 ft · 7¼ in target riser · 11¼ in treads · no pad.
      2. Slope3 ÷ 48 = 0.0625, or 0.750 in per foot.
      3. Round 1H = 36 in → 5 risers → run 4 × 11.25 = 45 in → H = 36 + 0.0625 × 45 = 38.81 in.
      4. Round 238.81 in needs 6 risers (5 would be 7.76 in, over the 7¾ in limit) → run 56.25 in → H = 39.52 in.
      5. Round 339.52 in still gives 6 risers → H stays 39.52 in. Done.
      6. ResultTotal rise 39.52 in (39-1/2"): 6 risers of 6.59 in (6-9/16") and 56¼ in of run. Measuring straight down would have given 36 in — 3½ in short.

      Typical floor-to-floor heights

      With ½ in drywall, ¾ in subfloor and ¾ in flooring on both levels:

      Finished total rise by ceiling height and floor framing
      Ceiling height2x10 joists11-7/8 in I-joists14 in I-joists
      8 ft (96 in)107-1/4" · 15 risers109-7/8" · 15 risers112" · 15 risers
      9 ft (108 in)119-1/4" · 16 risers121-7/8" · 17 risers124" · 17 risers
      10 ft (120 in)131-1/4" · 18 risers133-7/8" · 18 risers136" · 19 risers

      Riser counts are at a 7¼ in target under the IRC. Use the table to sanity-check a measurement — then enter your own layers, because a thicker subfloor or tile on a mortar bed changes the answer.

      Finished vs rough rise, and why flooring matters

      Framers often cut stairs before the flooring goes in, measuring from subfloor to subfloor — the rough rise. That works only if the flooring at the top and bottom is the same thickness: the whole stair moves up together. When they differ, the difference lands entirely on the top or bottom step.

      • Thicker flooring at the top (hardwood up, bare slab down) makes the top riser taller than the rest.
      • Thicker flooring at the bottom (tile on a mortar bed down, carpet up) makes the first riser shorter.

      The IRC allows risers within a flight to differ by no more than 3/8 in. When the finish difference is over that, lay the stair out from the finished rise and set the first-riser drop for the flooring still to come — the stair stringer calculator takes the bottom flooring into account.

      Deck and porch stairs on sloping ground

      On a sloping yard, the height under the deck edge is not the rise of the stair. The stair lands one run out, and the ground there may be several inches lower. How much changes with the slope:

      A 36 in deck with 7¼ in target risers and 11¼ in treads
      Ground falls over 4 ftTotal rise at landingRisersRun
      0 in (level)36.00 in5 × 7.20 in45 in
      1 in36.94 in5 × 7.39 in45 in
      2 in37.88 in5 × 7.58 in45 in
      3 in39.52 in6 × 6.59 in56¼ in
      4 in40.69 in6 × 6.78 in56¼ in

      Somewhere between a 2 in and a 3 in fall, the stair gains a step and its run grows by a full tread, which pushes the landing farther down the slope again. That feedback is why the rise has to be solved rather than measured once. If you pour a landing pad, its height above grade comes off the rise.

      On steep ground — more than about 2 in per foot — consider a level landing pad or a retaining step at the bottom, so the stair lands on something flat and the rise stops depending on exactly where the last tread ends.

      How to read your result

      Result ranges and next steps
      ValueGoodWatch outWhat to do
      Finish difference3/8 in or lessOver 3/8 inLay out from the finished rise; set the first-riser drop for the bottom flooring
      Straight-down vs landing riseLess than one riser apartMore than one riser apartUse the landing-point rise — the step count changes
      Ground slope2 in per foot or lessOver 2 in per footAdd a level landing pad or retaining step

      Take the finished total rise straight into the stair calculator to lay out risers and treads, then into the stringer calculator to cut them.

      Mistakes that give the wrong rise

      Using the ceiling heightAn 8 ft ceiling is a 107 to 112 in rise, not 96 in. Leaving out the floor framing loses one or two whole risers.

      Measuring subfloor to subfloor with different finishesHardwood upstairs over a bare slab moves the whole difference onto one step. Use the finished rise.

      Measuring straight down from a deck on a slopeThe stair lands farther out. On a ¾ in per foot fall, a 36 in deck becomes a 39½ in rise.

      Dropping a tape onto an uneven floorCarry a level line from the upper floor and measure at the exact landing spot.

      What this calculator does not cover

      Total rise FAQs

      How do I measure total rise for stairs?

      Measure from the finished lower floor to the finished upper floor at the point where the stair will be. Hold a long level or a straight board on the upper floor so it sticks out over the opening, and measure straight down from its underside to the lower floor; a laser level does the same job. Use the finished floor heights, not the subfloor.

      Should I measure total rise from the finished floor or the subfloor?

      From the finished floor. Every riser, including the first and last, must match within 3/8 in after flooring is installed. If the flooring is not down yet, add its thickness to your subfloor measurement, or build the rise up with this calculator and lay the stair out from the finished figure.

      What is a typical floor-to-floor height?

      About 107 to 112 in for an 8 ft ceiling, depending on the floor framing — 2x10 joists give about 107¼ in and 11-7/8 in I-joists about 109-7/8 in with ½ in drywall, ¾ in subfloor and ¾ in flooring. A 9 ft ceiling adds 12 in, which is usually one or two more risers.

      How does new flooring change the stairs?

      Flooring added at the top makes the top riser taller; flooring added at the bottom makes the bottom riser shorter. If the top and bottom flooring differ by more than 3/8 in, the end steps will be out of tolerance unless the stair is laid out from the finished rise and the first-riser drop is adjusted.

      How do I measure total rise for deck stairs on sloping ground?

      Measure the height from the deck surface to the ground where the stair starts, then measure how much the ground drops (or rises) over a few feet out from the deck. The stair lands farther out than the deck edge, so the rise at the landing is different from the straight-down height; this calculator moves the landing point as the stair grows until the numbers agree.

      Why does the landing point change the number of steps?

      Each step adds a tread of run, which moves the bottom of the stair farther out, where the ground is lower or higher. On ground falling ¾ in per foot, a 36 in deck becomes a 39½ in rise at the landing — enough to need 6 risers instead of 5.

      Does a concrete landing pad change the rise?

      Yes. The stair lands on top of the pad, so the pad thickness above grade comes off the rise. A 4 in pad on the same 36 in deck takes the rise from 39½ in down to about 34-13/16 in and removes a step.

      What if my floor is not level?

      Measure the rise at the exact spot where the bottom step will land, from a level line carried over from the upper floor. Dropping a tape from the upper floor onto a sloping lower floor gives the wrong figure for the landing point.

      Sources

      1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Riser, tread, nosing, width and handrail limits for homes; flight height limit at R311.7.3.
      2. American Softwood Lumber Standard (Voluntary Product Standard PS 20)National Institute of Standards and Technology. Dressed joist depths: 2x8 7¼ in, 2x10 9¼ in, 2x12 11¼ in.
      3. I-joist manufacturers’ product guidesCommon I-joist depths: 9½, 11-7/8, 14 and 16 in. Use the depth printed on your joists.
      4. Layer summation and slope correctionDerived from geometry: the finished rise is the sum of the layers, and the landing-point rise is found by iteration because the run depends on the riser count.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair layout calculatorsAll 6 tools for planning a straight stair — layout, stringers, total rise, angle, stairwell opening and footprint.View all 6

      Other stair calculator categories