Staircase Footprint Calculator

Enter your floor-to-floor height and stair width and see how much floor space six stair layouts need — straight, straight with a landing, L with a landing, L with winders, U-shaped and spiral — drawn to the same scale and ranked smallest first. Or enter the space you have and see which layouts fit.

By the Stair-Math TeamUpdated How we check this calculator

What do you want to know?

Your stair

in

Finished floor to finished floor. Not sure? Work out your total rise.

in

Every layout uses the same risers.

in

Riser face to riser face.

in

36 in is the IRC minimum; 42 in is roomier.

Quick picks:

Units

Your stair footprints

Every stair layout drawn in plan at the same scale, smallest first
All six layouts are drawn at one scale, so you can compare their size directly. In Fit my room the dashed outline is your space.

Layout check

    Solved with your numbers

      Assumptions: every layout uses the same risers, tread and width; L-stair landings are square and U-stair landings run across both flights; flights are split as evenly as possible with the extra riser in the lower flight; the nosing is counted once at the bottom; a 90° winder turn uses 3 winders. Stringers, walls and handrails are not included — add about 1½–3 in per side.

      Riser limits, flight limit and landing depth from the IRC (R311.7) and the codes listed under Sources; footprints follow from the geometry on this page. Tested against 6 worked cases, including a metric stair, a room where only a spiral fits and one where nothing fits. See the method · Sources

      How much space does a staircase need?

      It depends on three numbers: the total rise (floor to floor), the tread depth and the stair width. The rise sets the number of risers; each riser after the first adds one tread of length. Turning the stair trades length for width.

      Space needed for a 36 in wide stair (7¼ in target riser, 10½ in treads, 1 in nosing, IRC)
      Layout8 ft rise (96 in, 13 risers)9 ft rise (108 in, 15 risers)10 ft rise (120 in, 17 risers)
      Spiral, 60 in5' × 5' · 25.0 ft²5' × 5' · 25.0 ft²5' × 5' · 25.0 ft²
      Straight10' 7" × 3' · 31.8 ft²12' 4" × 3' · 37.0 ft²14' 1" × 3' · 42.3 ft²
      Straight with landing12' 8-1/2" × 3' · 38.1 ft²14' 5-1/2" × 3' · 43.4 ft²16' 2-1/2" × 3' · 48.6 ft²
      U-shaped8' 4" × 6' 2" · 51.4 ft²9' 2-1/2" × 6' 2" · 56.8 ft²10' 1" × 6' 2" · 62.2 ft²
      L with 3 winders7' 5-1/2" × 6' 6" · 48.5 ft²8' 4" × 7' 4-1/2" · 61.5 ft²9' 2-1/2" × 8' 3" · 76.0 ft²
      L with landing8' 4" × 7' 4-1/2" · 61.5 ft²9' 2-1/2" × 8' 3" · 76.0 ft²10' 1" × 9' 1-1/2" · 92.0 ft²

      Areas are the rectangle on plan (bounding area). Turning stairs leave part of that rectangle empty — the corner of an L, for example — so the calculator also shows the occupied area actually covered by treads and landings. Add 1½–3 in per side for stringers and wall finishes.

      How the staircase footprint calculator works

      Every layout uses the same risers, worked out exactly like the stair calculator. With n risers, T tread depth, N nosing, W stair width, Ld landing depth, g well gap and D spiral diameter, and flights split n1 = ceil(n ÷ 2) and n2 = n − n1:

      straight = ((n − 1) × T + N) × W

      straight with landing = ((n − 2) × T + Ld + N) × W

      L with landing = ((n1 − 1) × T + W + N) × (W + (n2 − 1) × T)

      L with 3 winders: s = n − 4 straight treads, split s1 + s2 → (s1 × T + W + N) × (W + s2 × T)

      U-shaped = (max((n1 − 1) × T + N, (n2 − 1) × T) + Ld) × (2W + g)

      spiral = D × D · areas ÷ 144 for ft², ÷ 1,000,000 for m²

      In Fit my room, each layout is tested against your length × width as entered, then turned 90°. A layout fits if both its sides fit; the spare space is what is left over in the orientation that fits.

      Worked examples

      Comparing layouts for a 9 ft rise

      1. Inputs108 in rise · 7¼ in target riser · 10½ in treads · 1 in nosing · 36 in wide · 36 in landings · 2 in well gap · 60 in spiral · IRC.
      2. Risers15 of 7.20 in (7-3/16"); flights split 8 + 7.
      3. Straight14 × 10.5 + 1 = 148 in × 36 in = 37.0 ft².
      4. TurnsU-shaped 110½ × 74 in (56.8 ft² bounding, 52.9 ft² occupied); L with winders 100 × 88½ in (61.5 / 38.1 ft²); L with landing 110½ × 99 in (76.0 / 43.4 ft²).
      5. RankingSpiral 25.0 → straight 37.0 → straight with landing 43.4 → U 56.8 → L with winders 61.5 → L with landing 76.0 ft².

      Fitting a 10 × 8 ft stair zone

      With the same stair and a 120 × 96 in space, the straight stair (148 in long) and the straight stair with landing do not fit. The spiral fits with 60 × 36 in to spare, the U-stair with 9½ × 22 in, and the L with winders with 20 × 7½ in. The L with a landing is 99 in wide and misses by 3 in either way round.

      Straight vs L vs U vs spiral stairs

      Trade-offs between stair layouts
      LayoutSpaceGood forWatch out for
      StraightLong and narrowSimplest and cheapest to build; easiest for moving furnitureNeeds a long wall and a long stairwell opening; a landing above the flight limit
      L with landingLargest rectangleTurns the stair into a corner; the landing is a rest and a safety breakThe corner of the rectangle is wasted unless used for storage
      L with windersSmaller than an L with landingFits a turn into less spaceWinders are narrow at the inside; they must meet walkline rules
      U-shapedShort and wideCompact, central stairs; shortens the opening aboveNeeds twice the stair width plus the well gap
      SpiralSmallestLofts, secondary access, tight cornersPoor for furniture; its own code rules for width, treads and headroom

      For the usual 9 ft rise the ranking is spiral, straight, straight with landing, U-shaped, L with winders and L with landing. For lower rises the L with winders can overtake the U-stair: at 96 in it needs 48.5 ft² against 51.4 ft². That is why the calculator ranks the layouts for your own numbers.

      Do I need a landing?

      Under the IRC, one flight may climb no more than 151 in; under the IBC, 144 in; in Australia, 18 risers. When your rise is over the limit, the straight row is marked "not allowed without a landing" and the straight-with-landing row becomes the straight option. Turning stairs already have a landing or winders at the turn.

      Landings must be at least as deep as the stair is wide, and the IRC also sets a 36 in minimum. Leave Landing depth blank and the calculator uses your stair width (36 in minimum for the IRC); enter a deeper landing if you want room to turn with furniture.

      Planning a basement or loft stair

      • Measure the zone you can give up, including clear floor at the top and bottom of the stair — at least a stair width of open floor at each end.
      • Run Fit my room. Layouts that fit are listed with their spare space, and each is tried both ways round.
      • If nothing fits: a steeper riser (within code) shortens every layout, a narrower stair (36 in minimum under the IRC) helps turning stairs most, and winders or a spiral fit the tightest spaces. A ship ladder is only for non-habitable spaces.
      • Check the opening above. The floor opening is separate from the footprint — size it with the stairwell opening calculator.

      How to read your result

      Result terms and next steps
      TermMeaningNext step
      Bounding areaThe rectangle the stair needs on planUse it to compare layouts and to plan rooms
      Occupied areaThe floor actually covered by treads and landingsThe difference is space you can use, e.g. under-stair storage
      Needs a landingA single straight flight would be over the flight limitUse the straight-with-landing or a turning layout
      Fits (turned)Fits only when rotated 90° from how you entered the roomCheck which wall the stair would start from

      Once you have chosen a layout, detail it: the stair calculator for straight stairs, or the L-shaped, U-shaped, winder and spiral calculators.

      What this calculator does not cover

      • Surface areas for carpet, flooring or paint — this page measures floor space only.
      • Detailed design of each layout: flight split, winder geometry and spiral code rules are on their own calculators.
      • The stairwell opening above the stair: use the stairwell opening calculator.
      • Ship ladders and alternating tread devices, which follow their own rules.

      Staircase footprint FAQs

      How much space does a staircase need?

      For a typical 9 ft floor-to-floor house (about 108 in of rise), a 36 in wide straight stair needs about 12 ft 4 in × 3 ft — 37 ft² of floor. An 8 ft basement rise (96 in) needs about 10 ft 7 in × 3 ft, and a 10 ft rise about 14 ft 1 in × 3 ft. Add the wall and stringer thickness on each side, plus clear floor at the top and bottom.

      How much space does an L-shaped staircase need?

      For a 108 in rise and a 36 in stair, an L with a square landing fits in a rectangle about 9 ft 2½ in × 8 ft 3 in, while the treads and landing cover only about 43 ft² of it. With 3 winders in the corner instead of a landing, the rectangle shrinks to about 8 ft 4 in × 7 ft 4½ in.

      How much space does a spiral staircase need?

      A square the size of its diameter: a 60 in spiral needs a 5 × 5 ft space and a 48 in spiral 4 × 4 ft, plus the stairwell opening above. Spirals use the least floor of any stair, but they carry furniture poorly and have their own code rules for clear width, tread depth and headroom.

      What is the most space-saving stair?

      A spiral, then a straight stair. Among turning stairs, an L with winders or a U-shaped stair usually needs a smaller rectangle than an L with a landing, because the winders or the half landing fold the run back on itself. Which is smallest for you depends on your rise, width and the shape of the space — the calculator ranks them for your numbers.

      How much floor area does a staircase take from each floor?

      On the lower floor, the stair covers its footprint — about 37 ft² for a 9 ft straight stair. On the upper floor it takes the stairwell opening, which is usually a little shorter than the stair; size it with the stairwell opening calculator.

      Do I need a landing on my stair?

      In the US, a single flight may rise at most 151 in under the IRC (144 in under the IBC), so a taller stair needs a landing. In Australia the limit is 18 risers per flight. Landings must be at least as deep as the stair is wide, and not less than 36 in under the IRC.

      What is the minimum stair width?

      36 in under the IRC for homes, measured above the handrail height; commercial stairs under the IBC are usually 44 in. A 36 in stair is the narrowest that will pass code in most US homes, and 42 in feels noticeably more generous.

      How do I plan stair space in a basement or loft?

      Measure the floor-to-floor height and the space available, then use Fit my room. If no stair fits, steepen the riser within code, narrow the stair to the 36 in minimum, consider winders or a spiral, or — for a non-habitable loft only — a ship ladder.

      Sources

      1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Riser and tread limits, 151 in flight limit (R311.7.3), 36 in width (R311.7.1) and landings at least as deep as the stair is wide and not less than 36 in (R311.7.6).
      2. International Building Code 2021, Chapter 10, Section 1011 — Stairways (opens in a new tab)International Code Council. Riser, tread and flight limits for commercial buildings.
      3. National Construction Code (opens in a new tab)Australian Building Codes Board. Riser, going and risers-per-flight limits.
      4. Spiral stair manufacturers’ kit sizesCommon spiral diameters of 48, 60, 66, 72 and 84 in. Spiral code geometry (clear width, tread depth, headroom) is covered by the spiral staircase calculator.
      5. Winders: three per 90° turnCommon building practice for a quarter-turn with winders. No single governing standard; winder tread depth is checked along the walkline under the codes.
      6. Footprint geometryDerived from geometry: each layout is the sum of its flights, landings and turns, using the same riser count and tread depth.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair layout calculatorsAll 6 tools for planning a straight stair — layout, stringers, total rise, angle, stairwell opening and footprint.View all 6

      Other stair calculator categories