Stair Angle Calculator

Enter a riser and tread to see how steep a stair is — angle, slope and ratio — whether it is comfortable, and whether it is within the maximum your code allows. Or pick a target angle and get the riser and tread that hit it, including the best riser count for your total rise.

By the Stair-Math TeamUpdated How we check this calculator

What do you want to know?

Your measurements

in

Top of one tread to the top of the next.

in

Riser face to riser face, without the nosing.

Quick picks:
Units

Your stair angle

Your steps drawn at their true angle, with the region's maximum angle as a dashed line
Drag the yellow handles to change the riser or tread — the angle follows. The dashed line is the steepest stair your code allows.

Angle check

    Solved with your numbers

      Assumptions: riser and tread are measured nosing to nosing, so the tread is the run without the nosing; all steps are equal; for a known total rise the target-angle solution uses the 2R + T = 25 in comfort rule. The region maximum angle checks steepness only — riser and tread limits are checked too, but a full code check covers more.

      Maximum angles derived from the IRC (R311.7), IBC (1011), NBC Canada and NCC riser and tread limits, and the 42° pitch in Approved Document K; steep-stair ranges from OSHA 1910.25. Tested against 8 worked cases. See the method · Sources

      What is the best angle for stairs?

      For a home, 32° to 36° is the sweet spot. Shallower stairs take a lot of floor space and can feel like a long stride; steeper ones feel like climbing. The comfort of a step comes from its proportions, not just its angle, which is why the calculator checks 2R + T alongside the angle.

      Angle of common riser and tread combinations
      Riser × treadAngleSlope2R + TClass
      6 × 12 in26.6°50.0%24.00 inGentle (outdoor, public)
      6½ × 11½ in29.5°56.5%24.50 inGentle
      7 × 11 in32.5°63.6%25.00 inTypical — the IBC limit
      7¼ × 10½ in34.6°69.0%25.00 inTypical residential
      7½ × 10 in36.9°75.0%25.00 inTypical residential
      7¾ × 10 in37.8°77.5%25.50 inThe IRC limit
      8¼ × 9 in42.5°91.7%25.50 inSteep stair
      9 × 6 in56.3°150.0%24.00 inShip ladder range

      How the stair angle calculator works

      angle θ = atan(riser ÷ tread)

      slope = riser ÷ tread × 100% · ratio = 1 : (tread ÷ riser) · rise per foot = 12 × riser ÷ tread

      2R + T · R + T · R × T — the three comfort rules

      level cut = θ · plumb cut = 90° − θ

      The tread is measured from riser face to riser face — the run of one step, without the nosing. Nosing overhangs the step below and does not change the angle.

      Comfort rules

      • 2R + T (twice the riser plus the tread): 24–25 in is good. Within an inch either side is borderline; beyond that the step feels short or long. UK and Australian stairs use 2R + G in millimetres: 550–700 mm is the code range and 600–650 mm is comfortable.
      • R + T: 17–18 in is good.
      • R × T: 70–75 in² is good (shown for inch units only).

      Two steps can share an angle and feel very different: 3½ on 5 in and 7 on 10 in are both 35°, but only the second fits a human stride. That is why a stair needs the comfort rules as well as the angle.

      Stair angle: the angle between the floor and the line through the steps, set by riser height over tread depth θ RiserTread θ = atan(riser ÷ tread)
      The stair angle is the angle between the floor and the line through the steps.

      Worked examples

      Checking a 7½ × 10½ in stair

      1. Angleatan(7.5 ÷ 10.5) = atan(0.714) = 35.5°.
      2. Slope and ratio71.4%, ratio 1 : 1.40, 8.57 in of rise per foot of run.
      3. Comfort2R + T = 25.50 in (borderline — just over the 24–25 in band); R + T = 18.00 in (good); R × T = 78.8 in² (borderline).
      4. CodeTypical residential; within the IRC maximum of 37.8°. Saw angles: level cut 35.5°, plumb cut 54.5°.

      Laying out a 108 in rise at 34°

      1. Comfort riserFor 2R + R ÷ tan 34° = 25 in: 25 ÷ (2 + 1 ÷ 0.6745) = 7.18 in.
      2. Risersround(108 ÷ 7.18) = 15, so each riser is 108 ÷ 15 = 7.20 in (7-3/16").
      3. Tread7.20 ÷ tan 34° = 10.67 in (10-11/16"); 14 treads give 149.44 in of run.
      4. Check2R + T = 25.07 in — a comfortable, legal IRC stair.

      Try the same rise at 45° and the calculator returns 13 risers of 8.31 in on 8.31 in treads: a comfortable stride, but the riser is over the 7¾ in IRC maximum and the tread under 10 in, so 45° is too steep for a code stair.

      Maximum stair angle by region

      Most codes do not state a maximum angle directly — they cap the riser and set a minimum tread. The steepest legal step gives the maximum angle:

      Maximum angle for standard stairs
      RegionSteepest legal stepMaximum angle
      US — IRC (homes)7¾ in riser on a 10 in tread37.8°
      US — IBC (commercial)7 in riser on an 11 in tread32.5°
      UK — Approved Document K (private stair)42° pitch stated directly; 220 mm rise max42.0°
      Canada (private stair)200 mm rise on a 255 mm run38.1°
      Australia — NCC190 mm riser on a 240 mm going38.4°

      Staying under the maximum angle is not enough on its own: a 9 in riser on a 12 in tread is only 36.9°, but its riser is over every limit. The calculator therefore also checks the riser and tread against your region. For a complete check of a built stair, use the stair code checker.

      Stair, steep stair, ship ladder or ladder?

      Angle classes used by the calculator
      AngleClassWhat it means
      Under 20°Very shallowTreads become very deep — consider a ramp or landscape steps
      20–30°GentleEasy to climb; public buildings and garden steps
      30–37.8°Typical residentialMost house stairs; 32–36° is the sweet spot
      37.8–50°Steep stairBeyond IRC rectangular-stair geometry; OSHA allows workplace stairs up to 50°
      50–70°Ship ladder / alternating treadOSHA range for ship stairs and alternating tread devices; used for lofts and plant rooms
      Over 70°LadderClimbed facing in; stair formulas no longer apply

      Turning an angle into a rise and run

      Choose From a target angle and keep the dimension you already know:

      • Riser height → tread = riser ÷ tan θ. A 7¼ in riser at 35° needs a 10.35 in tread (10-3/8").
      • Tread depth → riser = tread × tan θ. An 11 in tread at 32° needs a 6.87 in riser (6-7/8").
      • Total rise → the riser that makes 2R + T = 25 in at that angle, rounded to a whole number of risers. On a 108 in rise:
      A 108 in total rise at different target angles
      Target angleRisersRiserTreadTotal run
      30°166.75 in11.69 in175.37 in
      32°166.75 in10.80 in162.03 in
      34°157.20 in10.67 in149.44 in
      36°157.20 in9.91 in — under the 10 in IRC minimum138.74 in
      38°147.71 in9.87 in — under 10 in128.36 in

      Each degree steeper saves floor space but costs comfort and, past about 35° at this rise, the tread falls below the IRC minimum. To fit a stair into a fixed length instead, use Fit my space in the stair calculator.

      How to read your result

      Result ranges and next steps
      ValueGoodBorderline or failingWhat to do
      Angle30–37.8° for homes (32–36° best)Over your region maximumLower the riser or deepen the tread
      2R + T24–25 in (600–650 mm)23–24 or 25–26 in borderline; beyond is uncomfortableTrade riser height against tread depth
      R + T17–18 in16–17 or 18–19 in borderlineSame as above
      R × T70–75 in²65–70 or 75–80 in² borderlineSame as above

      When the angle and comfort look right, take the riser and tread to the stair calculator for the full layout, and use the level and plumb cut angles when you set up the saw for the stringers.

      Mistakes when measuring stair angle

      Including the nosing in the treadMeasure riser face to riser face. Adding a 1 in nosing to a 10 in tread makes a 37.8° stair read as 35.2°.

      Measuring one step of an old stairSteps in older stairs vary. Measure the total rise and total run and divide by the number of risers and treads for an average.

      Judging by angle aloneTwo stairs at the same angle can feel very different. Check 2R + T too.

      What this calculator does not cover

      • A full stair layout with run, stringer length and footprint: use the stair calculator.
      • Winder and spiral stairs, whose angle changes across the tread: see the winder and spiral calculators.
      • A complete code check of headroom, width, handrails and riser uniformity: use the stair code checker.
      • Ship ladders and alternating tread devices are designed to their own standards; check the rules that apply where you build.

      Stair angle FAQs

      What is the best angle for stairs?

      Between about 32° and 36° for a home. A 7 in riser on an 11 in tread is 32.5°, and 7¼ on 10½ is 34.6°; both feel natural because twice the riser plus the tread is close to 25 in, the length of an average stride on stairs.

      What is the maximum stair angle for residential code?

      Under the IRC it is 37.8° — the angle of the steepest legal step, a 7¾ in riser on a 10 in tread. The IBC allows 32.5° (7 in on 11 in), Approved Document K in the UK allows 42° for private stairs, Canada about 38.1° (200 mm on 255 mm) and the Australian NCC about 38.4° (190 mm on 240 mm).

      How do I calculate stair angle?

      Divide the riser by the tread and take the arctangent: angle = atan(riser ÷ tread). For a 7½ in riser on a 10½ in tread, 7.5 ÷ 10.5 = 0.714, and atan(0.714) = 35.5°. Measure the tread from riser face to riser face, without the nosing.

      What is the angle of a 7-11 stair?

      32.5°. A 7 in riser on an 11 in tread has a slope of 63.6% and a 2R + T of exactly 25 in, which is why 7-11 is often called the ideal stair — and it is also the steepest step the IBC allows for commercial stairs.

      What is the difference between stair angle, pitch and slope?

      Angle and pitch are the same thing — the steepness in degrees from horizontal. Slope is the same steepness written as rise over run, either as a percentage (75% for 7½ over 10) or a ratio (1 : 1.33). A 45° stair has a 100% slope.

      When does a stair become a ship ladder?

      Above about 50°. OSHA treats 30–50° as the range for standard workplace stairs and 50–70° for ship stairs and alternating tread devices; above 70° it is a ladder. Homes under the IRC stop at 37.8° for ordinary stairs.

      What is the maximum stair pitch in the UK?

      42° for a private stair under Approved Document K, with a maximum rise of 220 mm and 2R + G between 550 and 700 mm. Utility and general access stairs have lower limits.

      How do I turn an angle into a rise and run?

      Keep one dimension and solve the other with the tangent: tread = riser ÷ tan(angle), or riser = tread × tan(angle). If you know the total rise, the calculator finds the comfortable riser for the angle, rounds to a whole number of risers and gives the exact riser, tread and run.

      Sources

      1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Riser, tread, nosing, width and handrail limits for homes; flight height limit at R311.7.3.
      2. International Building Code 2021, Chapter 10, Section 1011 — Stairways (opens in a new tab)International Code Council. Riser, tread and flight limits for commercial buildings.
      3. Approved Document K: Protection from falling, collision and impact (opens in a new tab)UK Government (statutory guidance for England). Maximum riser, maximum pitch and 2R + G range.
      4. National Building Code of Canada 2020 (opens in a new tab)National Research Council Canada. Riser and run limits for stairs.
      5. National Construction Code (opens in a new tab)Australian Building Codes Board. Riser, going and risers-per-flight limits.
      6. OSHA 29 CFR 1910.25 — Stairways (opens in a new tab)US Occupational Safety and Health Administration. Workplace stair angles: standard stairs 30–50°, ship stairs and alternating tread devices 50–70°.
      7. The 2R + T step formula (Blondel-type rule)Common building practice for stair comfort; R + T and R × T are related shop rules. No single governing standard; the comfort bands on this page are shop practice, not code.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair layout calculatorsAll 6 tools for planning a straight stair — layout, stringers, total rise, angle, stairwell opening and footprint.View all 6

      Other stair calculator categories