Spiral Staircase Calculator

Choose a spiral diameter — or enter the floor opening you have — and get the risers, treads, tread angle, total rotation and exit, the tread depth at the walkline, the clear width, the headroom under the turn above and the floor opening, all checked against the IRC spiral stair rules.

By the Stair-Math TeamUpdated How we check this calculator

Where do you start?

Your spiral

in

Finished floor to finished floor. Not sure? Work out your total rise.

in

Spirals use taller risers than straight stairs — up to 9-1/2 in under the IRC.

Quick picks:

Direction going up
Units

Your spiral staircase

The spiral in plan, drawn to scale, with the walkline tread, clear width, floor opening and headroom
Plan view to scale: the dashed outer circle is the floor opening and the dashed inner circle the walkline. The section shows headroom under the tread one full turn above. In From floor opening, drag the opening edge.

Spiral code check

    Solved with your numbers

      Assumptions: all treads identical; the top landing platform is the last step, so there is one tread fewer than risers; the handrail allowance covers how far the handrail and balusters reach into the tread; headroom is measured from a tread to the underside of the tread one full turn above. Opening clearance is the total — 2 in is 1 in all round.

      Spiral rules from IRC R311.7.10.1 and R311.7.4 and the Australian NCC, listed under Sources; every output is worked out on this page with one consistent set of formulas. Tested against 6 worked cases, including a metric Australian kit, a loft spiral that is too narrow and two floor openings. See the method · Sources

      What size spiral staircase do I need?

      Clear width and floor opening by outside diameter (4½ in column, 1½ in handrail allowance, 2 in opening clearance)
      Outside diameterClear widthIRC 26 inFloor openingTypical use
      42 in17-1/4"No44"Loft access where allowed
      48 in20-1/4"No50"Loft and secondary access
      52 in22-1/4"No54"Secondary access
      60 in26-1/4"Yes62"The usual code-compliant home spiral
      64 in28-1/4"Yes66"Slightly roomier
      66 in29-1/4"Yes68"Comfortable for daily use
      72 in32-1/4"Yes74"Comfort; easier with small furniture
      84 in38-1/4"Yes86"Generous main spiral

      The clear width is measured from the centre column to the handrail, so a heavier column or a handrail that reaches further in costs width. The minimum diameter for 26 in of clear width is column + 2 × (26 + handrail allowance).

      Spiral stair code requirements

      IRC R311.7.10.1 spiral stair rules checked by the calculator
      RuleLimitHow it is measured here
      Clear widthAt least 26 in(diameter − column) ÷ 2 − handrail allowance
      Tread at the walklineAt least 6¾ inChord between nosings 12 in out from the column
      Walkline radiusNot more than 24½ inColumn radius + 12 in
      RiserNot more than 9½ inTotal rise ÷ risers
      HeadroomAt least 6 ft 6 inTreads per turn × riser − tread thickness
      TreadsAll identicalAssumed

      Edition note: this page follows the current IRC wording — 6¾ in at the walkline. Older editions asked for 7½ in measured 12 in from the narrow edge, and some pages still quote that rule; confirm which edition your building department enforces. For Australia the calculator gives an indicative check against the NCC spiral limits (riser 140–220 mm, going 210–370 mm, 2R + G 590–680 mm), using the going at mid-tread.

      How the spiral staircase calculator works

      With total rise H, target riser Rt, outside diameter D, column diameter dc, treads per full turn k, tread thickness tt, handrail allowance a and opening clearance c:

      risers n = round(H ÷ Rt), raised if the riser would be over 9½ in (220 mm in Australia) · R = H ÷ n · treads = n − 1

      tread angle θ = 360 ÷ k · rotation = treads × θ · exit = rotation mod 360

      walkline radius rw = dc ÷ 2 + 12 in · walkline tread = 2 × rw × sin(θ ÷ 2)

      clear width = (D − dc) ÷ 2 − a · headroom = k × R − tt

      mid-tread going = θ (radians) × (dc ÷ 2 + (D ÷ 2 − dc ÷ 2) ÷ 2) · floor opening = D + c

      In From floor opening the diameter is the opening less the clearance, D = opening − c, and everything else follows. When the clear width fails, the calculator gives the minimum diameter — and in opening mode the opening you would need.

      Worked examples

      A 5 ft kit on a 9 ft rise

      1. Inputs108 in rise · 60 in diameter · 4½ in column · 12 treads per turn · 9 in target riser · 1 in treads · 1½ in handrail allowance · IRC.
      2. Risers108 ÷ 9 = 12 risers of 9.00 in; 11 treads, each turning 30°, 330° in total.
      3. Walkline2.25 + 12 = 14.25 in out; tread there 2 × 14.25 × sin 15° = 7.38 in — over 6¾ in.
      4. Width(60 − 4.5) ÷ 2 − 1.5 = 26.25 in — just over 26 in.
      5. Headroom12 × 9 − 1 = 107 in; mid-tread going 8.44 in; floor opening 62 in. Every IRC check passes.

      Starting from a 66 in opening

      With a 2 in clearance the opening takes a 64 in spiral. On a 110 in rise that is 12 risers of 9.17 in, a 28.25 in clear width, a 7.38 in walkline tread and 109 in of headroom — a pass. A 52 in opening would only take a 50 in spiral with 21.25 in of clear width; for 26 in it needs to be at least 61.5 in.

      Treads per turn and headroom

      Effect of treads per full turn on a 60 in spiral (108 in rise, 12 risers of 9 in, 4½ in column, 1 in treads)
      Treads per 360°Tread angleWalkline treadHeadroomTotal rotation
      1132.7°8.03"98"360°
      1230.0°7.38"107"330°
      1327.7°6.82"116"305°
      1425.7°6.34" — under 6¾ in125"283°

      Headroom fails are fixed with more treads per turn or taller risers (up to 9½ in); walkline fails with fewer treads per turn. The rotation tells you where you step off at the top — plan the landing and the opening edge around it.

      How big a floor opening for a spiral staircase?

      The opening must clear the outside of the treads and the handrail as it passes through the floor. Kit makers usually ask for about 2 in more than the diameter — 1 in all round — so a 60 in spiral takes a 62 in opening. A square opening of that side works too, and leaves corners for the landing rail. If your opening is already framed, use From floor opening to see the largest spiral it takes and whether that spiral passes.

      Which way should a spiral turn?

      There is no code rule. Choose the direction so that you step off at the top towards where you want to go, and so that the handrail is on the side most people hold — for right-handed users, an anticlockwise climb puts the outer handrail on the right going up. Set the direction under Details to see the exit on the plan.

      What this calculator does not cover

      Spiral staircase FAQs

      What size spiral staircase do I need?

      Under the IRC the clear width from the column to the handrail must be at least 26 in, which with a 4½ in column and 1½ in of handrail takes a 60 in (5 ft) diameter — the most common residential size. Smaller kits (42–52 in) are sold for lofts and secondary access but do not meet the IRC width; 66–72 in feels far more comfortable.

      What is the minimum diameter for a spiral staircase?

      Column diameter + 2 × (26 in + handrail allowance). With a 4½ in column and a 1½ in allowance that is 4.5 + 2 × 27.5 = 59.5 in, so a 60 in kit. A thicker column or a bulkier handrail pushes it up.

      How many treads are in a spiral staircase?

      One fewer than the risers, because the top landing platform is the last step. A 9 ft (108 in) floor-to-floor with 9 in risers has 12 risers and 11 treads; at 12 treads per full turn they turn 330° in total.

      How much should each tread of a spiral turn?

      Usually 30° — 12 treads per full turn. Fewer treads per turn (bigger angles) give a deeper walkline tread but less headroom; more treads per turn give more headroom but shallower treads. On a 60 in spiral with a 4½ in column, 14 per turn drops the walkline tread to 6.34 in, under the 6¾ in IRC minimum.

      What are the code requirements for a spiral staircase?

      Under IRC R311.7.10.1: clear width at least 26 in at and below the handrail; tread depth at least 6¾ in at the walkline, with the walkline no more than 24½ in from the centre; all treads identical; risers no more than 9½ in; and at least 6 ft 6 in of headroom. Older editions measured the tread at 12 in from the narrow edge and asked for 7½ in, and some sites still quote that.

      How much headroom does a spiral staircase need?

      At least 6 ft 6 in (78 in) under the IRC. On a spiral the tightest headroom is under the tread one full turn above, so it is the riser height × treads per turn, less the tread thickness — 12 × 9 in − 1 in = 107 in for a typical stair.

      How big a floor opening does a spiral staircase need?

      The diameter plus a clearance for the handrail to pass — commonly 2 in in total, so a 62 in opening for a 60 in kit. Follow your kit maker’s figure, and check headroom where the stair passes under the edge of the opening.

      Can a spiral staircase be the main stair?

      Under the IRC, a spiral that meets R311.7.10.1 is a permitted stair type in a home. Even so, spirals are hard for moving furniture and many jurisdictions or lenders expect a conventional stair to bedrooms — check locally before relying on one as the only stair.

      Is a spiral or a ship ladder better for a loft?

      A spiral is a real stair you can walk down facing forward and carry light loads on; a ship ladder is steeper, takes much less floor and is only for spaces where the code allows it. If the loft is a habitable room, a code-compliant spiral (or a conventional stair) is usually needed.

      Sources

      1. International Residential Code 2021, Section R311.7.10.1 — Spiral stairways (opens in a new tab)International Code Council. Clear width at least 26 in at and below the handrail, tread depth at least 6¾ in at the walkline, walkline radius not more than 24½ in, identical treads, risers not more than 9½ in and headroom at least 6 ft 6 in; walkline defined in R311.7.4. Earlier editions measured spiral treads at 12 in from the narrow edge (7½ in).
      2. National Construction Code 2019, Volume Two, Table 3.9.1.1 — Riser and going dimensions (opens in a new tab)Australian Building Codes Board. Spiral stairs: riser 140–220 mm, going 210–370 mm, 2R + G 590–680 mm. The calculator applies them to the going at mid-tread as an indicative check.
      3. Spiral stair kit installation guidanceCommon manufacturer practice: a floor opening about 2 in larger than the stair diameter (1 in all round). No single governing standard — follow the kit maker’s instructions.
      4. Spiral geometryDerived from geometry: tread depth at a radius is the chord 2r sin(θ ÷ 2), the mid-tread going is the arc θ × r halfway out, and headroom is one full turn of risers less the tread thickness.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Turning & specialty stair calculatorsAll 7 tools for stairs that turn, wind or climb steeply — L-shaped, U-shaped, winder, spiral, curved, ship ladder and attic ladder.View all 7

      Other stair calculator categories