Curved Staircase Calculator

Enter the rise, inside radius, width and the angle the stair sweeps through and get the full geometry of a curved (helical) stair: risers, tread angle, tread depths at the narrow end, walkline and outside, the inner and outer stringer lengths with their pitches, the plan span — and the smallest sweep that passes the IRC rules for tapered treads.

By the Stair-Math TeamUpdated How we check this calculator

Your curve

in

Finished floor to finished floor. Not sure? Work out your total rise.

in

The riser count is rounded to fit your rise exactly.

in

From the centre of the curve to the inside edge of the clear width.

in

°

The plan angle the treads turn through — 90° is a quarter curve, 180° a half circle.

Quick picks:
Units

Your curved staircase

The curved stair in plan, drawn to scale, with the walkline and narrow-end depths and the plan span
Plan view to scale: tread lines radiate from the centre of the curve; the dashed arc is the walkline. Drag the inside end of the first tread to change the inside radius.

Curved stair check

    Solved with your numbers

      Assumptions: a circular plan; equal risers; tread lines radiating from the centre of the curve; stringer lengths measured on the stringer line at the tread nosings — fabricators add material for the top and bottom connections. Elliptical stairs are not covered; using their average radius gives only a rough check.

      Tapered treads are checked as winders under IRC R311.7.5.2.1, with the walkline from R311.7.4 and the riser limit from R311.7.5.1; the arcs, helices and chords are worked out on this page. Tested against 4 worked cases, including a metric stair and a curve too tight to pass. See the method · Sources

      How to calculate a curved staircase

      A curved stair is a straight stair wrapped round a circle. The risers come from the total rise as usual; the curve decides the shape of each tread. With total rise H, target riser Rt, inside radius Ri, clear width W and sweep φ (the plan angle the treads turn through):

      outside radius Ro = Ri + W · risers n = round(H ÷ Rt), raised if the riser would be over 7¾ in · R = H ÷ n · treads t = n − 1

      tread angle θ = φ ÷ t · walkline radius rw = Ri + 12 in

      narrow end = 2Ri sin(θ ÷ 2) · walkline = 2rw sin(θ ÷ 2) · outer end = 2Ro sin(θ ÷ 2)

      plan arcs Ai = Ri × φ, Ao = Ro × φ (φ in radians) · helical lengths Si = √(Ai² + H²), So = √(Ao² + H²)

      pitch: inner atan(H ÷ Ai), walkline atan(R ÷ walkline), outer atan(H ÷ Ao)

      plan span = 2Ro sin(φ ÷ 2) up to 180°, else 2Ro

      minimum sweep = t × max(2 asin(10 in ÷ 2rw), 2 asin(6 in ÷ 2Ri))

      Tread depths are chords — the straight distance between nosings, which is what a tape measures. In metric with no code selected the walkline is taken 300 mm in from the inside edge.

      Worked examples

      A 180° foyer stair

      1. Inputs108 in rise · 7½ in target riser · 60 in inside radius · 42 in wide · 180° sweep · IRC.
      2. Risers108 ÷ 7.5 = 14.4 → 14 risers of 7.71 in (7-11/16"); 13 treads of 180 ÷ 13 = 13.85°.
      3. TreadsNarrow end 2 × 60 × sin 6.92° = 14.46 in; walkline (72 in radius) 17.36 in; outer end (102 in) 24.59 in.
      4. StringersInner arc 60π = 188.50 in, helix 217.24 in at 29.8°; outer arc 320.44 in, helix 338.15 in at 18.6°.
      5. Plan and feelSpan 204 in (17 ft); walkline pitch 24.0°; 2R + T = 32.79 in — a long, easy stride.
      6. CodeBoth minimums pass. The smallest sweep that would still pass is 103.5°.

      When the curve is too tight

      Turn the same rise through 120° on a 48 in radius and the walkline tread drops to 9.66 in — just under 10 in. It needs a 124.3° sweep. On a 24 in radius over 90°, the walkline is 4.35 in and the narrow end 2.90 in, the inner stringer climbs at 70.8°, and the stair would need a 207.6° sweep to pass.

      Curved stair code requirements

      The IRC defines a winder as a tread whose edges are not parallel, so every tread on a curved stair is a winder and must meet R311.7.5.2.1:

      • At least 10 in deep at the walkline — 12 in from the inside edge of the clear width.
      • At least 6 in deep at any point within the clear width — in practice, at the narrow end.
      • Uniform: walkline depths within 3/8 in of each other. Equal treads on a true circle are identical; the tolerance matters on site.
      • Risers up to 7¾ in, as on a straight stair (R311.7.5.1).

      Outside the US, tapered-tread rules differ — choose None for geometry only and check your local code.

      How to calculate curved stringer length

      A curved stringer is a helix: as it turns through the sweep it climbs the full rise. Unroll it and it becomes a straight line whose base is the plan arc and whose height is the rise, so its true length is √(arc² + rise²). The inner stringer is shorter and steeper; the outer one longer and flatter. The pitch of each — atan(rise ÷ arc) — tells you how steep that edge of the stair will feel. Fabricators laminate or cut stringers longer than the helical length to allow for the floor and landing connections.

      Inside radius and sweep

      Minimum sweep to pass the IRC for a 108 in rise (14 risers, 13 treads), with each stair at 180°
      Inside radius × widthMinimum sweepAt 180°: walkline · narrow endPlan span at 180°Inner pitch at 180°
      36 × 36 in155.5°11.57" · 8.68"144" (12 ft)43.7°
      48 × 36 in124.3°14.46" · 11.57"168" (14 ft)35.6°
      60 × 42 in103.5°17.36" · 14.46"204" (17 ft)29.8°
      96 × 42 in69.0°26.04" · 23.14"276" (23 ft)19.7°

      A tighter radius needs more sweep for the same treads; a large radius can pass with a gentle quarter-to-half curve. Above about 50° the inner stringer feels like a ladder at the inside edge, so the calculator flags it. The table under your result shows your own stair at sweeps from 90° to 270°.

      How much space does a curved staircase need?

      The plan span is the straight distance across the outside ends of the curve — for a 180° sweep it is the full outside diameter, 2 × (inside radius + width). Add the landing at the top and clear floor at the bottom. Curved stairs are the most generous layout there is; to see how the space compares with straight, L, U and spiral stairs, use the staircase footprint calculator.

      Curved vs spiral stairs

      Curved and spiral stairs compared
      Curved (helical)Spiral
      SupportCurved stringers, open insideCentral column
      Inside radiusLarge — usually 3 ft or moreThe column radius
      RisersUp to 7¾ in (IRC)Up to 9½ in (IRC)
      Tread ruleWinder rules: 10 in at the walkline, 6 in narrow end6¾ in at the walkline, 26 in clear width
      SpaceA large room — often 12–20 ft acrossA 5–6 ft circle

      For a compact turning stair round a column, use the spiral staircase calculator.

      What this calculator does not cover

      • Elliptical or compound curves — the average radius gives only a rough check.
      • Straight flights with winders in a square corner: use the winder stair calculator.
      • Spiral stairs on a column, handrail length along the curve, structure and cost.

      Curved staircase FAQs

      How do you calculate a curved staircase?

      Find the risers from the total rise as for any stair, then divide the sweep — the angle the stair turns in plan — by the number of treads to get the tread angle. The depth of a tread at any radius is 2 × radius × sin(tread angle ÷ 2), so work it out at the inside edge, at the walkline (12 in out) and at the outside. Each stringer is a helix: its plan arc is radius × sweep in radians, and its true length is √(arc² + rise²).

      What are the code requirements for a curved stair?

      Under the IRC a tread whose edges are not parallel is a winder, so every curved-stair tread must be at least 10 in deep at the walkline and at least 6 in at any point within the clear width, with walkline depths within 3/8 in of each other. Risers are limited to 7¾ in, as on a straight stair.

      How do you calculate the length of a curved stringer?

      Multiply the stringer’s radius by the sweep in radians to get its plan arc, then take √(arc² + total rise²). For a 60 in inside radius over 180° and a 108 in rise, the inner stringer is √(188.50² + 108²) = 217.24 in long; the outer one, at 102 in radius, is 338.15 in. Allow extra for the connections.

      What is the minimum inside radius for a curved stair?

      It depends on the sweep and the number of treads. The narrow end needs 6 in, so the inside radius must be at least 3 in ÷ sin(tread angle ÷ 2), and the walkline (12 in further out) needs 10 in. For a 9 ft rise with 13 treads over 180°, a 36 in inside radius already gives 8.68 in at the narrow end and 11.57 in at the walkline; over 90° even 48 in is not enough.

      What is the difference between a curved and a spiral staircase?

      A spiral winds tightly round a central column, with a small inside radius, taller risers and its own code rules (26 in clear width, 6¾ in at the walkline). A curved stair has a large open inside radius, no column, normal risers and treads that meet the winder rules — it takes far more floor and is usually a feature stair.

      How much space does a curved staircase need?

      For a half-circle (180°) sweep the stair spans twice the outside radius: a 60 in inside radius with a 42 in stair spans 204 in (17 ft). A quarter curve spans about 1.4 × the outside radius. The plan span in the result is the width of room the curve covers.

      How many steps are in a curved staircase?

      The same as a straight stair for the same rise — a 9 ft rise with about 7½ in risers needs 14 risers and 13 treads. The curve changes the shape of the treads, not their number.

      Sources

      1. International Residential Code 2021, Sections R311.7.4, R311.7.5.1 and R311.7.5.2.1 (opens in a new tab)International Code Council. Walkline 12 in from the inside edge of the clear width (R311.7.4); 7¾ in maximum riser (R311.7.5.1); winder treads at least 10 in at the walkline, at least 6 in at any point within the clear width and within 3/8 in of each other (R311.7.5.2.1). Chapter 2 defines a winder as a tread with non-parallel edges, which makes curved-stair treads winders.
      2. Helix and chord geometryDerived from geometry: tread depth at radius r is the chord 2r sin(θ ÷ 2); a stringer at radius r turning through the sweep has a plan arc r × sweep (radians) and a true length √(arc² + rise²); the plan span is the chord 2Ro sin(sweep ÷ 2) up to 180°.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Turning & specialty stair calculatorsAll 7 tools for stairs that turn, wind or climb steeply — L-shaped, U-shaped, winder, spiral, curved, ship ladder and attic ladder.View all 7

      Other stair calculator categories