Stair Paint & Stain Calculator

Pick the parts you are finishing — treads, risers, stringer or skirt sides, balusters and handrail — then the finish, the coverage from your can and the number of coats. You get the area of each part, the total per coat, the gallons (or litres) needed with waste, and the gallon-and-quart or tin combination to buy.

By the Stair-Math TeamUpdated How we check this calculator

Your stair and finish

risers

in

in

in

in

Finish the treads
Finish the risers
ft²/gal · m²/L

From the can label — ft² per gallon with inch units, m² per litre with metric. Blank = typical latex paint (350 ft²/gal, 10 m²/L).

Quick picks:

Units

Your finish

The stair parts being finished and the area of each
Side view with the parts being finished picked out, and the area of each part per coat.

Finishing notes

    Solved with your numbers

      Assumptions: treads finished on the top face plus the front edge of the nosing; risers on the front face; balusters on every face over their full height; handrail all the way round; no deduction for brackets or fixings. Walls, ceiling and the underside of the stair are not included.

      Areas come from the stair geometry and quantities from the coverage on your can; typical paint coverage and waste ranges are listed under Sources. Tested against 5 worked cases, including clear coat on treads only, balusters and handrail only, stain on porous wood and a metric stair. See the method · Sources

      How the stair paint calculator works

      With n risers of height R, n − 1 treads of depth T, nosing N with front-edge thickness e and width W:

      treads = (n − 1) × ((T + N) × W + e × W) · risers = n × R × W

      sides = sides × (n − 1) × √(R² + T²) × visible height

      balusters = count × perimeter × height (square: 4 × side; round: π × diameter) · handrail = length × perimeter

      finish = area × coats × (1 + waste) ÷ coverage

      Areas in square inches are divided by 144 for ft². To buy, the gallons are turned into quarts and rounded up; three quarts or more becomes a gallon, because a gallon costs about the same as three quarts. In metric the litres are matched to the 0.75, 2.5 or 5 L tin size that wastes least.

      Worked examples

      Paint on treads and risers

      1. Inputs14 risers of 7¼ in · 10¼ in treads · 1 in nosing, 1 in thick · 36 in wide · paint at 350 ft²/gal · 2 coats · 10% waste.
      2. Treads13 × ((10.25 + 1) × 36 + 1 × 36) = 5,733 in² = 39.81 ft².
      3. Risers14 × 7.25 × 36 = 3,654 in² = 25.38 ft². Total 65.19 ft² per coat.
      4. Paint65.19 × 2 × 1.10 ÷ 350 = 0.410 gal → 1.64 quarts → buy 2 quarts.

      Balusters and handrail only

      28 square balusters 1½ in × 38 in: 28 × 6 × 38 = 6,384 in² = 44.33 ft². A 180 in handrail 7.07 in around: 8.84 ft². Two coats of paint at 350 ft²/gal with 10% waste: 0.334 gal — 2 quarts.

      Metric staircase

      13 risers of 190 mm, 250 mm goings with 20 mm nosings 25 mm thick, 900 mm wide: 5.409 m² of treads and risers. Two coats at 10 m²/L with 10% waste need 1.19 L — two 0.75 L tins.

      Coverage and coats by finish

      Typical figures — always use the coverage printed on your can
      FinishTypical coverageUsual coats on treads
      Latex floor or trim paint350–400 ft²/gal (9–10 m²/L)2, over primer
      Oil-based enamel300–350 ft²/gal2, over primer
      Wood stain150–300 ft²/gal on bare wood1, wiped off
      Floor polyurethane400–600 ft²/gal3

      Coverage drops on raw or porous wood and when spraying. Use the label’s lower figure for rough or porous surfaces rather than adding a coat. For the stair in the first worked example, the paint needed by coats is:

      14-riser stair, treads and risers (65.19 ft²), 350 ft²/gal, 10% waste
      CoatsPaintBuy
      10.205 gal1 qt
      20.410 gal2 qt
      30.615 gal1 gal
      40.820 gal1 gal

      Balusters and handrail

      Each baluster is finished on every face over its full height. A 1½ in square baluster 38 in tall has 1.58 ft²; a 1½ in round one has 1.24 ft², because a circle has π × d of surface around it instead of 4 × d. With 28 balusters that is 44 ft² square or 35 ft² round — more than all the risers of a 14-riser stair. A handrail is its length times the distance around its profile: 7.07 in for a 2¼ in round rail, about 7½ in for a typical 2⅝ in moulded rail. Count balusters with the baluster spacing calculator and measure the rail with the stair handrail calculator. In the UK these are spindles and the banister.

      Finishing treads safely

      • Floor-rated finish: treads take foot traffic, so use a floor paint, porch enamel or floor polyurethane, not wall or trim paint.
      • Not gloss: high-gloss paint and clear coat are slippery, especially in socks. Choose satin or matt, or stir in an anti-slip additive for the last coat.
      • Keep the stair usable: finish every other tread, then the rest once the first set has cured, so the stair stays in use.
      • Primer: bare wood, knots and filler need primer, which is a separate product — run the calculator again for it with one coat.

      What this calculator does not cover

      Stair paint and stain FAQs

      How much paint do I need for stairs?

      Less than most people expect. A 14-riser stair 36 in wide with 10¼ in treads and 7¼ in risers has about 65 ft² of treads and risers. Two coats at 350 ft² per gallon with 10% waste come to 0.41 gal — two quarts. A third coat takes it to about 0.61 gal, so buy a gallon.

      How much paint for balusters and a handrail?

      Balusters have more surface than they look: a 1½ in square baluster 38 in tall has about 1.58 ft² over its four faces, so 28 of them come to 44 ft² — more than all the risers. A 15 ft handrail 2¼ in round adds about 9 ft². Two coats of both fit in two quarts.

      How many coats of paint on stair treads?

      Two coats of a floor-rated paint over a primer is the usual minimum on treads; risers can take two coats of ordinary trim paint. Let each coat cure fully before using the stair, and use the next tread up as a stepping stone if you paint alternate treads.

      How much stain do I need for stairs?

      Stain soaks into bare wood, so its coverage is lower than paint — often 150–300 ft² per gallon on raw pine or oak. Enter the label figure for porous wood and one coat: a 14-riser stair with one stained side needs about 0.35 gal, which is two quarts.

      How much polyurethane do I need for stair treads?

      Three coats of a floor polyurethane at around 500 ft² per gallon on 13 treads use about 0.26 gal — a little over a quart, so buy two quarts. Use the coverage on your can: water-based and oil-based floor finishes differ.

      What is the best paint for stair treads?

      A floor and porch paint or a floor-rated enamel, in satin or matt rather than gloss, which is slippery underfoot. Mix in an anti-slip additive or use a paint with grit if the stair is steep, outdoors or used in socks.

      Should I paint or stain stairs?

      Stain and clear coat show the wood and suit hardwood treads such as oak; paint hides softwood, filler and old damage. A common mix is stained and clear-coated treads with painted risers and stringers, which hides scuffs on the risers.

      Do I need primer on stairs?

      Yes on bare wood, knots, filler and old gloss. Primer is a separate product with its own coverage, so run the calculator again with the primer’s label figure and one coat.

      Sources

      1. Product label coveragePaint, stain and clear-coat makers print the spreading rate on the can and data sheet; that figure governs, and often gives a lower value for rough or porous surfaces.
      2. Typical paint coveragePainting trade guidance: latex paint about 350–400 ft² per gallon (about 9–10 m² per litre), oil-based about 300–350 ft² per gallon on smooth primed surfaces.
      3. Waste allowancePainting practice: about 10–15% for cutting in, brush and tray loss.
      4. Surface areasDerived from geometry: tread top plus nosing edge, riser face, stringer slope length × visible height, baluster perimeter × height and handrail length × perimeter.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair materials & cost calculatorsAll 6 tools for what a stair takes to build or finish — lumber, concrete, carpet, flooring, paint and cost.View all 6

      Other stair calculator categories