Stair Carpet Calculator

Enter your risers, treads and nosing and choose waterfall or Hollywood (cap and band). For wall-to-wall carpet you get the run up the stair, how many strips fit across the roll, the length of roll to buy and the square yards you actually pay for, with pad and tack strip. For a runner you get the length to buy, the stair rods and the pad.

By the Stair-Math TeamUpdated How we check this calculator

Carpet or runner?

Your stair

risers

in

in

in

Installation style
in

Quick picks:

Units

Your carpet

Side view of the carpet path over the steps, and the roll (or runner) from above
Side view of the bottom steps with the carpet wrap, and the strips cut from the roll (or the runner with its rods). Drag the strip edge to change the stair width.

Carpet notes

    Solved with your numbers

      Assumptions: equal risers and treads; pieces may be joined at the back of a tread; the pad covers the treads and nosings (not the risers); one tack strip at the back of each tread and one at the foot of each riser. Strips are cut along the roll so the pile runs down the stair.

      Lengths are worked out from the step geometry on this page; roll widths, waste and runner allowances follow flooring trade practice, listed under Sources. Tested against 5 worked cases, including Hollywood with a landing, a stair too wide for more than one strip and a metric runner. See the method · Sources

      How to measure carpet for stairs

      With n risers of height R, n − 1 treads of depth T, nosing overhang N and nosing thickness d:

      wrap = N (waterfall) or 2N + d (Hollywood) · per step = R + T + wrap

      run L = n × R + (n − 1) × (T + wrap) + landing

      strips across the roll = floor(roll width ÷ carpet width) · roll length = L ÷ strips · buy = roll length × (1 + waste), rounded up to the foot

      area bought = length bought × roll width · pad = ((n − 1) × (T + N) + landing) × W · tack strip = 2 × W × (n − 1) (+ W at a landing)

      runner: buy = L × (1 + waste) · rods = n − 1 · rod = runner + 4 in · pad = runner − 2 in wide × (n − 1) × (T + N) long

      Carpet is cut in strips along the roll so the pile runs down the stair, and several strips can sit side by side across a wide roll — that is why a 36 in stair needs only a short length of a 12 ft roll.

      Worked examples

      Fourteen steps, waterfall

      1. Inputs14 risers of 7¼ in · 10¼ in treads · 1 in nosing · waterfall · 36 in wide · 12 ft roll · 10% waste · $30 per sq yd.
      2. Per step7.25 + 10.25 + 1 = 18.50 in.
      3. Run14 × 7.25 + 13 × 11.25 = 247.75 in (20.65 ft); net 6.88 sq yd.
      4. RollFour 36 in strips fit across 12 ft, each 61.94 in long; with waste buy 6 ft of roll — 8.00 sq yd, $240.
      5. Extras4.06 sq yd of pad and 78 ft of tack strip.

      Hollywood with a landing

      Cap and band wraps 3 in per step (2 × 1 in + 1 in thick nose), so each step takes 20.50 in. With a 36 in landing the run is 309.75 in; buy 8 ft of roll (10.67 sq yd), 5.06 sq yd of pad and 81 ft of tack strip.

      A 27 in runner

      The same stair takes a 247.75 in runner — buy 23 ft with waste — with 13 rods 31 in long and a 25 in pad 12.19 ft long. At $25 a foot that is $575.

      How much carpet for 13 or 14 stairs?

      7¼ in risers, 10¼ in treads, 1 in nosing, waterfall, 36 in wide, 12 ft roll, 10% waste
      RisersRunRoll to buyArea boughtPad27 in runner
      10173.75 in4 ft5.33 sq yd2.81 sq yd16 ft
      12210.75 in5 ft6.67 sq yd3.44 sq yd20 ft
      13229.25 in6 ft8.00 sq yd3.75 sq yd22 ft
      14247.75 in6 ft8.00 sq yd4.06 sq yd23 ft
      16284.75 in7 ft9.33 sq yd4.69 sq yd27 ft

      Waterfall vs Hollywood stair carpet

      The two ways to fit carpet over a nosing
      WaterfallHollywood (cap and band)
      LookFalls straight from the nose to the next treadWraps tightly under the nose and down the riser
      Carpet per stepRiser + tread + overhangRiser + tread + 2 × overhang + nose thickness
      FittingFaster, suits thick carpetMore labour, suits thinner carpet and runners

      Buying carpet from a roll

      Carpet is sold by the length of roll you cut, not by the area you lay. The calculator fits as many strips across the roll as the stair width allows, then gives the roll length to buy and the area you pay for. A 36 in stair fits four strips across a 12 ft roll; a 78 in stair fits only one, so you buy about twice the net area — the table under your result compares roll widths. A stair wider than the roll needs a side seam.

      Stair runners

      A runner is sold by the foot (or metre) in a fixed width. Choose a width that leaves an even margin of wood each side — 27 in on a 36 in stair leaves 4½ in. Each tread gets a rod at the back, about 4 in longer than the runner, and a pad about 2 in narrower so it stays hidden. Finish the exposed wood beside the runner with the stair paint calculator.

      Pad, tack strip and installing

      • Fit tack strip (carpet gripper) at the back of each tread and the foot of each riser, pins pointing towards the angle.
      • Staple pad to each tread and over the nose, stopping short of the tack strip.
      • Start at the bottom, pile running down, and join pieces only at the back of a tread.
      • For winders, cut each step separately and allow 15–25% waste.

      What this calculator does not cover

      Stair carpet FAQs

      How much carpet do I need for stairs?

      Each step takes the riser plus the tread plus the wrap round the nosing — about 18½ in for a 7¼ in riser, 10¼ in tread and 1 in nosing. Fourteen risers need a run of about 20 ft 8 in. A 36 in stair cut four strips across a 12 ft roll, so you buy just 6 ft of roll: 8 sq yd.

      How much carpet for 13 or 14 stairs?

      With 7¼ in risers, 10¼ in treads and 1 in nosings on a 36 in stair: 13 risers need a 229 in run and 14 risers 248 in. From a 12 ft roll both come to 6 ft of roll — 8 sq yd including 10% waste. A runner needs about 22–23 ft.

      What is the difference between waterfall and Hollywood stair carpet?

      Waterfall carpet runs straight down from the nose of one tread to the back of the next, leaving a gap behind it. Hollywood (cap and band) wraps the carpet tightly under each nosing and down the riser, which looks tailored but uses more carpet — about 2 in more per step.

      What is the standard width of a stair runner?

      Runners are commonly 22–32 in wide, leaving 3–6 in of wood showing each side on a 36 in stair; 27 in is a popular size. Rods are about 4 in longer than the runner, and the pad about 2 in narrower so it does not show.

      How many stair rods do I need?

      One per tread, fixed at the back of the tread where it meets the riser — 13 for a 14-riser stair. Each rod is the runner width plus about 4 in for the brackets.

      How much carpet pad do I need for stairs?

      Pad goes on the treads and over the nosings, not on the risers. For 13 treads 11¼ in deep (with nosing) on a 36 in stair that is about 4 sq yd. A runner pad is cut to the runner length on the treads and about 2 in narrower than the runner.

      Where do you start carpeting stairs?

      Start at the bottom and work up, with the pile running down the stair. Fit tack strip at the back of each tread and the foot of each riser, staple the pad to the treads, and join pieces only at the back of a tread so a seam never sits on a nose.

      How do I measure carpet for winder steps?

      Measure each winder at its widest point and its deepest, treat each as a rectangle, and allow 15–25% waste — winders are cut individually and waste a lot more than straight steps.

      How much does it cost to carpet stairs?

      Enter your price per square yard (or per foot for a runner) and the calculator multiplies it by what you actually buy. For installed costs including labour and removal, use the staircase cost calculator.

      Sources

      1. Broadloom roll widthsCommon US trade practice: carpet sold in 12 ft rolls, with 13.2 ft and 15 ft also available; 4 m rolls in metric markets.
      2. Waste allowancesFlooring trade practice: about 10% for straight stairs, 15–25% for winders and curved steps.
      3. Runner rods and padCommon runner-installer practice: rods about 4 in (100 mm) longer than the runner; pad about 2 in (50 mm) narrower.
      4. Carpet geometryDerived from geometry: per step = riser + tread + wrap (waterfall: nosing overhang; Hollywood: 2 × overhang + nosing thickness).

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair materials & cost calculatorsAll 6 tools for what a stair takes to build or finish — lumber, concrete, carpet, flooring, paint and cost.View all 6

      Other stair calculator categories