Stair Flooring Calculator

Choose planks with stair nose, tile with bullnose, or retread kits. For planks you get the rows per tread, the planks, boxes and stair-nose sticks to buy, with a warning when the stair is wider than a plank. For tile you get the area, tiles, boxes and bullnose pieces. For retreads you get the kits and returns — and how much the bottom and top risers change.

By the Stair-Math TeamUpdated How we check this calculator

What are you laying?

Your stair

risers

in

For retreads, the existing riser height.

in

in

in

in

in

in

Common: 72 in, 90 in (7-1/2 ft), 94 in.

in

Risers
Quick picks:
Nose at the top floor edge

Units

Your stair flooring

Side view of the steps with stair nose or bullnose, and one tread from above with the plank rows or tiles
Side view and one tread from above, to scale. Drag the first row edge to change the plank width; for retreads, drag the first tread to change the thickness.

Flooring notes

    Solved with your numbers

      Assumptions: each tread is covered with full-width rows; offcuts are not reused between treads (a little conservative); the stair nose or bullnose sits at the front of each tread; riser kits cover each riser. Landings are measured separately as a small room.

      The 3/8 in riser limit is IRC R311.7.5.1; stair-nose lengths come from maker listings and waste ranges from flooring trade practice, listed under Sources; the counts are worked out on this page. Tested against 7 worked cases, including a stair wider than the plank, metric tile and retreads that fail and pass. See the method · Sources

      How the stair flooring calculator works

      Planks and stair nose. With n risers, n − 1 treads of depth T, nosing N, width W, plank width p and length L, and a stair nose that covers d of the tread:

      tread field = T + N − d · rows per tread = ceil(field ÷ p) · rows per riser = ceil(R ÷ p)

      if W ≤ L: treads per plank = floor(L ÷ W), planks = ceil(treads × rows ÷ treads per plank); if W > L: planks = treads × rows × ceil(W ÷ L)

      boxes = ceil(planks × p × L × (1 + waste) ÷ box coverage) · noses = treads + 1 · sticks = ceil(noses ÷ floor(stick ÷ W))

      Tile and bullnose. field = T + N − bullnose depth; area = treads × W × field + risers × R × W; tiles and boxes from the area with waste; bullnose = (treads + 1) × ceil(W ÷ piece length), plus 10%.

      Retread kits. One tread kit per tread and one riser kit per riser, in the shortest standard width (36, 42, 48, 60 or 72 in) that covers the stair; return caps = treads × open sides. New bottom riser = R + thickness; new top riser = R − thickness.

      Worked examples

      LVP on a 14-riser stair

      1. Inputs14 risers of 7¼ in · 10¼ in treads · 1 in nosing · 36 in wide · 7 × 48 in planks · 94 in stair nose covering 2¼ in · risers covered · 20 ft² boxes · 10% waste.
      2. Treads10.25 + 1 − 2.25 = 9.00 in of field → 2 rows; one 48 in plank covers one 36 in tread → 26 planks.
      3. Risers7.25 ÷ 7 → 2 rows → 28 planks. 54 planks in all, 126 ft² → 7 boxes.
      4. Noses13 treads + the top floor edge = 14 noses; two per 94 in stick → 7 sticks.

      Porcelain with bullnose

      12 × 24 in tile with a 3 in bullnose leaves an 8.25 in field: 26.81 ft² of treads and 25.38 ft² of risers, 52.19 ft² in all — 31 tiles (4 boxes of 16 ft²) with 15% waste, and 42 bullnose pieces, 47 with the extra 10%.

      Retreads that unbalance the stair

      ¾ in retreads on 7¼ in risers make the bottom riser 8.00 in and the top 6.50 in — a 1½ in spread, far over 3/8 in. 5/16 in cap retreads give 7.562 in and 6.938 in, within the limit.

      LVP and laminate on stairs

      Plank rows on a 10¼ in tread with a 1 in nosing and a stair nose covering 2¼ in (9 in field)
      Plank widthRows per treadRows per 7¼ in riser
      5 in22
      6 in22
      7 in22
      9 in11

      Wide planks can cover a tread field in one row, which halves the cutting. Choose planks at least as long as the stair is wide: on a 54 in stair, 48 in planks need a joint in every row and double the plank count. Glue every piece down and finish each tread with the maker’s stair nose.

      Stair noses, treads and retreads

      • Stair nose: a moulding over the front edge of planks laid on the old tread — one per tread plus one at the top floor edge.
      • One-piece stair tread: covers the whole tread including the nose; no planks on the tread.
      • Retread kit: a new solid tread (and riser) over the old stair, usually after cutting back the old nosing. Open sides need a return cap on each tread.

      Tile on stairs

      Tile treads need a bullnose or a metal nosing on every edge and a tile rated for slip resistance on stairs. The bullnose takes the front few inches of each tread, so the field tile covers less; riser tiles are cut to the riser height. Allow about 15% waste — tread and riser tiles are nearly all cut pieces.

      Do retreads change the riser height?

      Yes. Every new tread sits on top of the old one, so every tread rises by the retread thickness. The middle risers stay the same, but the bottom riser grows and the top riser shrinks — unless the floors at the bottom and top are raised too. The IRC allows only 3/8 in between the tallest and shortest riser, so ¾ in retreads laid straight on top fail. The fixes are to cut back the old nosings and trim the treads so the retread sits lower, to use thin cap retreads, or to adjust the bottom and top steps. Check the finished stair with the stair code checker, and see how floor finishes change the rise with the total rise calculator.

      What this calculator does not cover

      Stair flooring FAQs

      How much LVP do I need for stairs?

      Count rows rather than area: each tread needs enough plank rows to cover the tread behind the stair nose, and each riser enough rows to cover its height. For 14 risers with 10¼ in treads, 1 in nosings and 7 × 48 in planks on a 36 in stair that is 54 planks — about 126 ft², or 7 boxes of 20 ft² with 10% waste.

      How many stair noses do I need?

      One for every tread, plus one at the top floor edge — 14 for a 14-riser stair. Divide by how many stair widths you get from one stick: a 94 in stick gives two 36 in noses, so you need 7 sticks.

      What is the difference between a stair nose, a stair tread and a retread kit?

      A stair nose is a moulding that finishes the front edge of planks laid on a tread. A one-piece stair tread replaces the planks and nose on each step. A retread kit is a full tread (and often a riser) made to cover an existing stair after the old nosings are cut back.

      Can you put laminate or LVP on stairs?

      Yes, if you glue the planks down and finish every front edge with the maker’s stair nose or a one-piece tread. Never leave a plank edge as the nosing — it will chip and is a trip risk. Planks at least as long as the stair is wide avoid a joint in every row.

      How many boxes of flooring for 14 stairs?

      With 7 × 48 in planks on a 36 in stair, about 7 boxes of 20 ft². Wide 9 in planks on a 48 in stair need about 5 boxes of 24 ft². The stair-nose sticks are bought separately.

      Bullnose tile or metal nosing for stairs?

      Either works if every tread edge is covered. Bullnose tiles give a seamless look; a metal or PVC stair nosing is tougher and often has an anti-slip strip. Use tiles rated for stairs and allow about 15% waste for cuts.

      Do retreads change the riser height?

      Yes. Laying a new tread on top raises every tread by its thickness, so the bottom riser grows and the top riser shrinks by that amount. With ¾ in retreads on 7¼ in risers the bottom riser becomes 8 in and the top 6½ in — more than the 3/8 in the IRC allows. Cut back the old nosings and trim the treads, or use thin cap retreads.

      How much waste should I allow for stair flooring?

      More than for a floor, because each tread is cut separately: about 5–10% for LVP, 8–12% for laminate, 10–15% for hardwood and about 15% for tile.

      Sources

      1. International Residential Code 2021, Section R311.7.5.1 — Risers (opens in a new tab)International Code Council. The greatest riser height in a flight may not exceed the smallest by more than 3/8 in — the limit used for the retread check.
      2. Stair-nose stick lengthsManufacturer product listings: stair noses commonly sold in about 72 in, 90 in (7½ ft) and 94 in lengths.
      3. Waste allowancesFlooring trade practice: LVP 5–10%, laminate 8–12%, hardwood 10–15%, tile about 15% on stairs.
      4. Flooring geometryDerived from geometry: rows = ceil(field depth ÷ plank width); planks from treads per plank or planks per row; bullnose pieces per nosing = ceil(width ÷ piece length).

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair materials & cost calculatorsAll 6 tools for what a stair takes to build or finish — lumber, concrete, carpet, flooring, paint and cost.View all 6

      Other stair calculator categories