Stair Design7 min readPublished

Landing vs Winder Stairs: Which Turn Is Better?

Every stair that turns has to choose: a flat landing in the corner, or tapered winder treads that keep climbing through it. This guide builds the same 9 ft L-shaped stair both ways and compares what each costs in floor space, comfort, safety and code margin — so you can see exactly what the 10½ in saved by winders buys you.

By the Stair-Math TeamUpdated

The same stair, built two ways

To compare the two turns fairly, both stairs below are identical except for the corner: 108 in (9 ft) floor to floor, 36 in wide, 15 risers of 7.2 in and 10½ in treads, turning 90° to the right. The left one turns on a square landing; the right one replaces the landing with three 30° winders.

Plans to scale of the same 9 ft L-shaped stair turning at a square landing (110.5 by 99 in) and with three winders (100 by 88.5 in)LANDING TURN110.5 × 99 in · 43.4 ft²THREE WINDERS100 × 88.5 in · 38.1 ft²

Swipe the drawing sideways to see all of it.

The same 9 ft L-stair drawn to one scale. Yellow is the landing; the dashed red arc on the winders is the walkline, 12 in from the narrow side.
Landing turn vs three winders, same 108 in climb
Landing turnThree winders
Treads8 + landing + 66 + 3 winders + 5
Outline110.5 × 99 in100 × 88.5 in
Floor covered43.4 ft²38.1 ft²
Depth on the turn36 × 36 in flat12.23 in at the walkline, 6.02 in at the narrow end
Rest pointYes, at 57.6 inNo
Code in US homesAny stairAny stair, winder rules apply
Commercial exit stair (IBC)AllowedNot allowed

Winders save exactly one tread on each leg — 10½ in each way — because the three tapered treads climb through the corner instead of standing still on a landing. That is 5.3 ft² or about 12% of the floor. It does not sound like much, but in an older house or a basement those 10½ in are often the difference between a stair that fits a hallway and one that does not.

What makes a winder legal

A rectangular tread has one depth. A winder tapers from a narrow end at the inside of the turn to a wide end at the outside, so the IRC measures it along the walkline — a line 12 in in from the narrow side, roughly where a person holding the inside rail puts their feet.

Plan of a three-winder quarter turn: 6.02 in deep at the narrow end and 12.23 in at the walkline, 12 in from the narrow side1234

3 winders × 30°

36 in wide, 7¼ in risers

  1. 1Inside radius 11-5/8 in
  2. 26.02 in deep at the narrow end
    IRC minimum 6 in
  3. 312.23 in deep at the walkline
    IRC minimum 10 in
  4. 4Walkline, 12 in from the narrow side
Three 30° winders turning a 36 in stair, measured the way the IRC measures them.
Winder rules in a US home (IRC 2021)
RuleLimit
Depth at the walkline10 in minimum, measured 12 in from the narrow side
Depth at any point6 in minimum — the narrow end decides this
ConsistencyDeepest and shallowest winder at the walkline within 3/8 in
RisersSame 7¾ in maximum and 3/8 in consistency as the rest of the flight
HandrailContinuous for the flight; may be interrupted by a newel post at the turn

Two consequences are easy to miss. First, the walkline rule compares winders only with each other — the IRC does not require them to match the straight treads, so a 12.23 in winder next to 10½ in treads is legal even though your stride has to change on the turn. Second, the 6 in minimum applies everywhere on the tread, so the classic pie-slice winder that comes to a point at a corner post fails outright.

Outside the US the idea is the same with different numbers: in England, Approved Document K measures tapered treads at the centre line on narrower stairs and asks for at least 50 mm at the narrow end.

Inside radius decides whether winders pass

For three 30° winders, both depths come straight from the inside radius — the distance from the corner point the treads radiate from to where they start. Depth at any radius is 2 × radius × sin 15°:

Three 30° winders: depth by inside radius
Inside radiusNarrow end (min 6 in)Walkline (min 10 in)Result
0 in (pointed)0 in6.21 inFails both
6 in3.11 in9.32 inFails both
9 in4.66 in10.87 inFails the narrow end
11⅝ in6.02 in12.23 inPasses
15 in7.76 in13.98 inPasses with margin
18 in9.32 in15.53 inPasses; turn grows to 54 in square

The narrow end decides it: the walkline passes from a 9 in radius, but the 6 in minimum needs at least 11⅝ in. A bigger radius makes the inside easier to walk but pushes the outside corner out, so the turn stops fitting in a 36 in square. Other splits change the numbers — two 45° winders pass from a 7⅞ in radius, but each one turns your foot through 45°, which feels abrupt; four 22½° winders need about a 15⅜ in radius but give 10.68 in at the walkline, almost exactly matching 10½ in straight treads, at the cost of a larger corner.

Safety and comfort: why landings win

Stairs are walked by rhythm. After two or three steps your legs commit to a stride, and a step that breaks the pattern is where people stumble. A landing is a clean break — you stop, turn on a flat floor and start again. A winder turn keeps you climbing while the tread depth changes under your feet: 10½ in, then about 12¼ in on the winders if you walk the walkline, then 10½ in again. Walk closer to the inside and the winders shrink toward 6 in, roughly half an adult shoe.

Landing advantages

  • A flat place to stop, rest and turn
  • A fall on the upper flight stops at the landing instead of the bottom
  • The same tread depth on every step you take
  • Room to pass someone or turn with a load

Winder risks

  • Narrow ends are easy to misjudge, especially coming down on the inside
  • The safe path is near the outside wall, but the inside is the short way
  • Anyone who holds an inside rail walks on the narrow side
  • A winder turn at the top means the first steps down are tapered

If you build winders, three choices take most of the risk out: put the turn near the bottom of the flight rather than the top, give the inside a generous radius rather than the minimum, and fit a handrail on the outside (wide) side so people are drawn to the deeper part of the treads. Good light on the turn matters more on a winder stair than on any other.

Furniture, handrails and building

Furniture. A landing is where a sofa, a box spring or a mattress gets tipped on end and turned. A 36 × 36 in landing is the code minimum and is tight for that; 42–48 in makes a real difference. Winders give you no flat surface at all — long items have to be carried around the turn at an angle, which makes moving day noticeably harder.

Handrails. On a landing stair the rail usually stops at a newel post at the landing and starts again on the next flight, which the IRC allows at a turn. On winders the outside rail can run continuously around the corner; the inside rail turns over the narrow ends at a steep pitch and is often cut short at a newel.

Building. A landing is framed like a small floor — joists, a header and support at the corner — and the two flights are plain straight flights. Winders are more carpentry: each tread is a different shape, the skirt boards and stringers have to follow the turn, and the treads are usually carried on stacked framed platforms. Both turns put an L or U stair at roughly twice the starting cost of a straight one; winders trade framing for finish carpentry rather than saving money.

Which turn to choose

  1. Start with the landingIf the landing version fits, build it. It is the safer, more comfortable and easier-to-move-into stair, and it costs about the same.
  2. Use winders to win back 10½ inWhen the landing version is one tread too long on one or both legs — a basement, a cottage, a stair squeezed beside a chimney — winders are the standard answer.
  3. Put the winders lowA turn at the bottom of the flight is easier to walk and safer to fall on than one at the top.
  4. Size the inside radius, not just the treadsFor three 30° winders, an inside radius under 11⅝ in fails the 6 in rule no matter how deep the walkline is. More radius is more comfort.
  5. Check where the stair isWinders are fine in a house; a commercial or multi-family exit stair has to turn on landings.

The same logic applies to U-shaped stairs, which can turn with a half landing or with six winders. For the other ways to turn or shorten a stair, see our guide to staircase types.

Landings and winders: common questions

Are winder stairs safe?

They are legal and can be safe when built to the rules, but they are less forgiving than a landing. The tread depth changes from step to step, and the narrow ends are only about 6 in deep — roughly half an adult shoe. Most missteps happen coming down on the inside of the turn. A handrail on the wide (outside) side and good lighting help.

How much space do winders save compared with a landing?

On a 9 ft (108 in) L-stair 36 in wide, three winders replace a 36 × 36 in landing and save one tread’s depth on each leg: the outline goes from 110.5 × 99 in to 100 × 88.5 in, and the floor covered from 43.4 ft² to 38.1 ft² — about 12%.

What is the minimum depth for a winder tread?

Under the IRC, at least 10 in measured at the walkline, 12 in in from the narrow side, and at least 6 in at the narrowest point. Within a flight, the deepest winder at the walkline may not exceed the shallowest by more than 3/8 in.

Can you have winders at the top of a staircase?

Yes, winders can be placed at the top, bottom or middle of a flight under the IRC, as long as each meets the walkline and 6 in rules. Winders at the top are the hardest to descend because the first steps down are tapered; many designers keep the turn near the bottom for that reason.

What is a kite winder?

The middle tread of a three-winder quarter turn. It is shaped like a kite because it is the only winder that touches both outside walls of the corner.

Do commercial buildings allow winder stairs?

Not in a required exit stair. The IBC permits winders only inside an individual dwelling unit, and spiral stairs only in limited places. Office and public stairs turn at landings.

How deep must a stair landing be?

At least 36 in in the direction of travel and as wide as the stair under the IRC. On an L-stair with a 36 in wide flight that means a 36 × 36 in square landing at minimum; a deeper landing makes turning long furniture easier.

Sources

  1. International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Winder treads and the 12 in walkline (R311.7.5.2.1), tread and riser limits (R311.7.5), landings 36 in deep and as wide as the stair (R311.7.6), handrail continuity and the newel-post exception at turns (R311.7.8.4).
  2. International Building Code 2021, Section 1011 — Stairways (opens in a new tab)International Code Council. Winder treads not permitted in means of egress stairways except within a dwelling unit (1011.5.3); walkline and minimum winder depths where winders are allowed.
  3. Approved Document K: Protection from falling, collision and impact (opens in a new tab)UK Government (statutory guidance for England). Tapered treads: going measured at the centre line on stairs under 1 m wide, at least 50 mm at the narrow end, consistent going on consecutive tapered treads.

Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

More stair design guides