A stair, part by part
The stair below is the one most American houses have between floors: 108 in (9 ft) from finished floor to finished floor, 36 in wide, 15 risers of 7.2 in and 14 treads of 10½ in with a 1 in nosing. The main parts are numbered on it, drawn to scale, and every number quoted later comes from this stair.
Swipe the drawing sideways to see all of it.
One 9 ft stair
15 risers × 7.2 in · 14 treads × 10½ in · 36 in wide
- 1Tread — the board you stand on
- 2Riser — the vertical face of each step
- 3Nosing — the tread edge that overhangs the riser
- 4Stringer — the sloping board that carries the steps
- 5Newel post — anchors the rail at the bottom, top and turns
- 6Baluster — the vertical infill of the guard
- 7Handrail — 34–38 in above the nosing line
- 8Nosing line — the slope through every nosing; rails and headroom are measured from it
- 9Headroom — at least 6 ft 8 in clear above the nosing line
- 10Header — the beam at the edge of the floor opening
- 11Total rise — finished floor to finished floor, 108 in here
- 12Total run — first riser to last riser, 147 in here
- 13Landing — the level floor at the top (and bottom)
- 14Guard — stops a fall off the open edge of the landing
The parts fall into five groups, and the rest of this guide takes them in order: the steps themselves, the measurements that set their size, the structure that holds them up, the railings that keep people on them, and the opening in the floor above that gives them headroom.
Treads, risers and nosings
A step is one tread and the riser below it. The tread is the horizontal board you stand on; the riser is the vertical face between one tread and the next. On a closed-riser stair the riser is a board; on an open-riser stair it is just the gap.
The nosing is the front edge of the tread where it projects past the riser below. It matters more than it looks: climbing, it gives your toe and heel extra room; descending, it is the edge the ball of your foot lands on. The IRC requires a nosing of ¾ to 1¼ in whenever the tread is less than 11 in deep, with a radius no larger than 9/16 in and every nosing in a flight within 3/8 in of the others.
| Part | Limit | Our stair |
|---|---|---|
| Riser height | 7¾ in maximum | 7.2 in |
| Tread depth (nosing to nosing) | 10 in minimum | 10½ in |
| Nosing projection | ¾–1¼ in when the tread is under 11 in | 1 in |
| Variation within a flight | 3/8 in, largest to smallest riser or tread | 0 in |
| Open risers | 4 in sphere may not pass, when total rise is over 30 in | Closed risers |
| Riser slope | Vertical, or up to 30° from vertical | Vertical |
Note what is measured: tread depth is the horizontal distance from one nosing to the next, not the size of the board. A 10½ in tread with a 1 in nosing is cut from an 11½ in deep board — exactly the stock size sold as “stair tread”. The variation limit is the rule people break most: a first step made taller to make up a floor-height error is the classic trip, because legs set their stride on the first two or three steps and expect the rest to match.
Two special treads have their own names. A bullnose or starter step is a bottom tread with one or both ends rounded, often wider than the stair so the newel can sit on it. A winder is a tapered tread that turns the stair; it is covered with landings below.
Rise, run and the numbers that size a stair
Every stair starts from one measurement — the total rise, from the finished surface of the lower floor to the finished surface of the upper floor. Measure it after flooring thickness is known: adding ¾ in of hardwood upstairs after the stair is built makes the top riser ¾ in taller than the rest and breaks the 3/8 in rule.
- Total rise
- 108 in
- Risers
- 15 × 7.2 in
- Treads
- 14 × 10½ in
- Total run
- 147 in
The unit rise is the height of one riser: total rise ÷ number of risers, here 108 ÷ 15 = 7.2 in. The unit run (also called the going) is the depth of one tread, nosing to nosing. There is always one more riser than tread on a stair between two floors, because the last riser steps you onto the upper floor itself — so the total run, the horizontal length from the face of the first riser to the face of the last, is 14 × 10½ = 147 in.
Rise and run together set the pitch or angle: atan(7.2 ÷ 10½) = 34.4°. Residential stairs live between about 30° and 37°; the code maximum works out to 37.8° (7¾ over 10). A flight is an unbroken run of steps between floors or landings, and the IRC caps one flight at 151 in of rise — anything taller needs a landing partway.
Measure and correct your total rise (including flooring) with the total rise calculator
Then turn it into risers, treads, run and angle with the stair calculator
Stringers, carriages and what holds a stair up
The stringers are the sloping members that carry the steps from floor to floor. Almost every wood stair uses one of three kinds:
| Type | How the steps attach | Where you see it |
|---|---|---|
| Cut (open) stringer | Sawtooth notches cut into a 2x12; treads and risers sit on top | Basements, decks, and the hidden structure under most finished stairs |
| Closed (housed) stringer | Grooves routed into the face; tread and riser ends slide in and are wedged and glued | Finished interior stairs where the tread ends are hidden |
| Mono-stringer | One central steel or laminated beam; treads cantilever left and right | Modern open stairs |
A cut stringer is only as strong as the wood left below the notches — the throat. Notching a 2x12 (11¼ in actual) for our 7.2 × 10½ in steps leaves a little over 5 in, which is the minimum prescriptive deck rules use; the same notch in a 2x10 (9¼ in actual) leaves only about 3¼ in, which is why 2x10 stringers are a common inspection failure. Those rules also keep cut stringers no more than 18 in apart and limit their unsupported horizontal span to 6 ft — so a 36 in stair takes three stringers, and a 147 in run needs support partway, usually a wall or a post-and-beam under the middle.
A carriage is a cut stringer used as hidden structure under a finished face; a skirt board (or skirting) is the finished board on the wall side that covers the joint between steps and wall. Where an open stringer is exposed on the open side, the end of each tread is finished with a tread return, a small mitred piece that hides the end grain. At the top the stringers hang from the floor framing, and at the bottom they bear on the floor; a kick plate fastened to the floor keeps the bottom from sliding.
The loads are higher than most people expect. The IRC designs stairs for 40 lb per ft² across the whole flight and 300 lb concentrated on any one tread — which is what decides tread thickness and stringer spacing.
Get the framing-square settings, throat and board length for your stringers with the stair stringer calculator
Handrails, guards and balusters
“Railing” covers two jobs, and the code treats them separately. A handrail is the rail you hold for balance. A guard is the barrier that stops you falling off an open edge. On many stairs one assembly does both — the top of the guard is the handrail — but the rules for each still apply.
| Part | What it does | IRC 2021 |
|---|---|---|
| Handrail | Something to grip all the way up | Required on at least one side when a flight has 4 or more risers; 34–38 in above the nosing line; continuous for the full flight; 1½ in clear of the wall |
| Handrail profile | Has to be graspable | Round 1¼–2 in diameter, or an equivalent shape with 4–6¼ in perimeter |
| Guard | Stops a fall off an open side | Required where the drop is more than 30 in; 36 in high at landings, 34 in on the open side of a stair |
| Balusters (spindles) | Fill the guard | No opening that passes a 4 in sphere; 4-3/8 in on the stair; 6 in at the triangle under the bottom rail |
| Newel post | Anchors the rail at ends and turns | Handrails and guards resist 200 lb in any direction |
The rest of the vocabulary is about how the rail starts, turns and ends. A volute is the spiral scroll that finishes a handrail over a bullnose step; a turnout is a gentler sideways curve. A gooseneck is the vertical bend where a sloped rail rises to meet a higher landing rail. A rosette is the round plate where a rail ends against a wall. The shoe rail (bottom rail) runs along the stringer and takes the bottom of the balusters, and the fillet is the strip that fills the gaps between them in the shoe rail’s groove. The whole assembly — newels, rails, balusters — is the balustrade.
With the 4-3/8 in rule, two balusters per tread are usually enough on a 10½ in tread with 1¼ in square balusters; three per tread are common with thinner or round ones.
Count balusters and set the gaps for your stair with the baluster spacing calculator
Work out handrail length, heights and brackets with the stair handrail calculator
Landings, winders and the turn
A landing is a level platform at the top, bottom or middle of a stair. The IRC requires one at the top and bottom of every stair, as wide as the stair and at least 36 in deep in the direction of travel (the top landing can be skipped on an interior stair only if no door swings over the steps). A landing partway up is a quarter-space landing when the stair turns 90° and a half-space landing when it turns 180°.
Winders turn the stair without a landing, using tapered treads. Because a tapered tread has no single depth, the code measures it along the walkline, 12 in in from the narrow side: at least 10 in deep there and at least 6 in deep at the narrowest point. A kite winder is the middle, kite-shaped tread of a three-winder turn.
For the shape of the whole stair — straight, L, U, spiral or curved — see the types of staircases, which builds this same 9 ft stair every way.
Stairwell, header and headroom
The stairwell is the opening in the upper floor that the stair climbs through. Its edges are framed with headers (across the ends of the cut joists) and doubled trimmers (alongside the opening). The opening has to be long enough for headroom: at least 6 ft 8 in clear, measured vertically from the nosing line to the lowest thing above, usually the header.
- Headroom
- 6 ft 8 in (80 in)
- Floor structure
- 12 in
- Opening length
- about 135 in
- Opening width
- 36 in + wall finishes
For our stair, the underside of the upper floor sits 96 in up (108 in minus a 12 in floor). The nosing line has to be no higher than 16 in where it passes under the header, which happens about 12 in in from the first riser — so the opening runs from there to the top of the stair, about 135 in of a 147 in total run. A thicker floor or a taller ceiling changes that number, which is why the stairwell is sized from the stair and not the other way round.
Size the opening for your floor depth and headroom with the stairwell opening calculator
Same part, different names
Stair terms vary by region and trade. The ones below cause the most confusion on drawings and orders:
| Term | Also called | Note |
|---|---|---|
| Run | Going, tread run, unit run | Horizontal depth of one step, nosing to nosing — not the board size |
| Baluster | Spindle, picket | “Picket” is more common on decks and fences |
| Handrail | Banister, rail | “Banister” can also mean the whole balustrade |
| Stringer | Stringboard, string | A hidden cut stringer is often called a carriage |
| Nosing line | Pitch line | The line handrail height and headroom are measured from |
| Landing | Platform, half-pace (UK) | Quarter-space for a 90° turn, half-space for 180° |
| Bullnose step | Starter step | Rounded bottom tread, often wider than the flight |
When you order parts or brief a builder, give dimensions as well as names — “10½ in run, 11½ in tread board, 1 in nosing” leaves no room for doubt in any of these vocabularies.
Stair parts: common questions
What is the difference between a tread and a step?
A tread is the horizontal board you stand on. A step is the whole unit — one tread plus the riser below it. A stair with 15 risers has 14 treads, because the upper floor acts as the last “tread”.
What is a stair nosing?
The front edge of a tread that overhangs the riser below it. Under the IRC a nosing of ¾ to 1¼ in is required when the tread is less than 11 in deep, and all nosings in a flight must match within 3/8 in. The nosing gives your heel room when you climb and catches the ball of your foot when you descend.
What is the difference between a banister, a handrail and a balustrade?
A handrail is the rail you hold. A balustrade is the whole guard assembly — handrail or top rail, balusters, bottom rail and newel posts. “Banister” is the everyday word for either, most often the handrail; builders and inspectors avoid it because it is ambiguous.
What is the stringer on a staircase?
The sloping board on each side (and often in the middle) that carries the treads and risers. A cut or open stringer is notched into a sawtooth so the treads sit on top; a closed or housed stringer has grooves routed into its face so the tread ends are hidden. A single central steel beam is called a mono-stringer.
What is a newel post?
The large post at the bottom, top and each turn of a staircase that anchors the handrail and guard. It is the strongest point of the railing: the IRC requires handrails and guards to resist a 200 lb load in any direction, and the newel is where most of that load ends up.
How many risers does a 9 ft stair have?
With a finished-floor-to-finished-floor rise of 108 in and a 7¼ in target, 108 ÷ 7.25 = 14.9, so it rounds to 15 risers of 7.2 in. It has 14 treads, which at 10½ in each gives a total run of 147 in.
What is stair headroom and how is it measured?
The clear height above the stair, measured vertically from the sloped line through the nosings (the nosing line) to the lowest thing overhead — usually the header at the edge of the stairwell opening. The IRC minimum is 6 ft 8 in; spiral stairs need 6 ft 6 in.
Sources
- International Residential Code 2021, Chapter 3, Section R311.7 — Stairways (opens in a new tab)International Code Council. Width (R311.7.1), headroom (R311.7.2), 151 in flight limit (R311.7.3), risers, treads, nosings and open risers (R311.7.5), landings (R311.7.6), handrail height, continuity and grip (R311.7.8), winders and walkline (R311.7.5.2.1).
- International Residential Code 2021, Section R312 — Guards (opens in a new tab)International Code Council. Guards where a walking surface is more than 30 in above the floor or grade; 36 in height, 34 in on the open sides of stairs; 4 in sphere openings, 4-3/8 in on stairs, 6 in at the riser–tread triangle (R312.1).
- International Residential Code 2021, Table R301.5 — Minimum uniformly distributed live loads (opens in a new tab)International Code Council. Stairs 40 psf and a 300 lb concentrated load on any tread; guards and handrails 200 lb in any direction; guard infill 50 lb on 1 ft².
- Prescriptive deck construction guides (US model guides)Cut stair stringers: at least 5 in of throat below each notch, no more than 18 in apart and no more than 6 ft horizontal span unless supported.
Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.
Calculators for this guide
- Stair CalculatorRisers, treads, run and code check in one layout
- Stair Stringer CalculatorCut the stringers: square settings, throat, board to buy
- Stairwell Opening & Headroom CalculatorSize the floor opening for legal headroom
- Stair Handrail CalculatorWork out how much handrail to buy
- Baluster Spacing CalculatorSpace balusters evenly and pass the 4 in rule
- Total Rise CalculatorGet the right finished rise first