Egress Stair Width Calculator

Enter the occupant load — or the floor area and use, and the calculator works out the load from the IBC occupant load factors. You get the total stair capacity at 0.3 in per occupant (0.2 in with sprinklers and a voice alarm system), the width each stair needs with the 36 or 44 in minimum, the number of exits the load needs, and whether the stairs still carry half the load with one blocked.

By the Stair-Math TeamUpdated How we check this calculator

What do you know?

Your building

people

The largest floor the stairs serve.

stairs

Sprinklered with an emergency voice/alarm system
Occupancy Group H or I-2
Quick picks:
Units

Your egress stairs

Required stair capacity against the stairs provided
Each stair drawn to its width, against the total capacity the occupants need and the half that must remain if one stair is lost.

Egress checks

    Solved with your numbers

      Assumptions: IBC 2021 method; stairs of equal width; the largest floor the stairs serve governs; floor area entered net or gross as the use factor states. An early-planning check — the fire or code consultant confirms the occupancy, the load and the exit layout.

      Factors and limits are quoted from IBC 2021 Chapter 10, with the section beside each check; Sources lists them. Tested against 6 worked cases, including the sprinkler reduction, an office and a restaurant from floor area, a floor under 50 occupants and a standing venue that needs four exits. See the method · Sources

      How the egress stair width calculator works

      occupant load = ceil(floor area ÷ load factor) (or the load you enter)

      factor = 0.2 in per occupant with sprinklers + voice alarm (not Group H or I-2), otherwise 0.3 in

      total capacity = load × factor · minimum = 36 in under 50 occupants, else 44 in

      width per stair = max(minimum, total ÷ stairs)

      exits = 2 (≤ 500), 3 (501–1,000), 4 (over 1,000) · loss of one: (stairs − 1) × width ≥ 50% × total

      Floor area in m² is converted to ft² (× 10.764) before dividing by the factor. Widths are shown in inches or millimetres to suit your units.

      Occupant load factors

      IBC Table 1004.5 factors used by the calculator
      Useft² per occupantArea
      Assembly, unconcentrated (tables and chairs)15net
      Assembly, concentrated (chairs only)7net
      Assembly, standing space5net
      Business areas150gross
      Educational, classrooms20net
      Exercise rooms50gross
      Industrial areas100gross
      Mercantile60gross
      Residential200gross
      Warehouses500gross

      Net area leaves out corridors, stairs, toilets, walls and fixed equipment; gross area is everything inside the exterior walls. Mixed floors add the load of each use.

      Worked examples

      A restaurant floor

      1. Load6,000 ft² net ÷ 15 = 400 occupants.
      2. Capacity400 × 0.3 in = 120 in of stair in total.
      3. Per stair120 ÷ 2 = 60 in, more than the 44 in minimum, so each stair is 60 in wide.
      4. Checks400 occupants need 2 exits — met. With one stair blocked, 60 in remains, exactly half of 120 in — met.

      An office floor

      12,000 ft² gross ÷ 150 = 80 occupants; 80 × 0.3 = 24 in, so the 44 in minimum governs and each of two stairs is 44 in wide.

      A standing-room venue

      6,000 ft² ÷ 5 = 1,200 occupants need 360 in of stair — 180 in each across two stairs — and at least four exits, so two stairs fail: add stairs or exits.

      Does a sprinkler system reduce stair width?

      Only when the building has both an automatic sprinkler system and an emergency voice/alarm communication system; then the factor drops from 0.3 to 0.2 in per occupant. Group H (high-hazard) and I-2 (hospitals and nursing homes) get no reduction. For 200 occupants the capacity falls from 60 in to 40 in — but each stair must still be 44 in, so the reduction only pays on large floors where capacity, not the minimum, governs.

      How many exits are required?

      Minimum exits per story, IBC Table 1006.3.3
      Occupant load per storyExits
      1–5002
      501–1,0003
      More than 1,0004

      The exits must also be spread so that losing any one leaves at least half the required capacity. Stairs of equal width meet this with two or more stairs once each meets its share. Check each stair’s risers, treads and handrails with the stair code checker.

      What this calculator does not cover

      • Travel distance, exit separation and exit access — set by IBC Sections 1006, 1007 and 1017.
      • Stairs in homes: use the stair code checker with the IRC.
      • Codes outside the US: this is the IBC method — check your national code.
      • Stair layout and headroom: use the stair calculator and the stairwell opening calculator.

      Egress stair width FAQs

      How do you calculate egress stair width?

      Multiply the occupant load by 0.3 in per occupant to get the total stair capacity, then share it across the stairs. Each stair must also be at least 44 in wide (36 in when fewer than 50 people use it). For 400 people and two stairs: 400 × 0.3 = 120 in, so each stair needs 60 in.

      What does 0.3 inch per occupant mean?

      It is the IBC stairway capacity factor: every person the stair serves needs 0.3 in of stair width. 200 people need 60 in of stair in total. Level exits such as doors and corridors use 0.2 in per occupant.

      Does a sprinkler system reduce stair width?

      Only with an emergency voice/alarm communication system as well. With both, the IBC allows 0.2 in per occupant instead of 0.3, except in Group H and I-2 occupancies. On most floors the 44 in minimum still governs, so the reduction often changes nothing.

      What is the minimum width of a commercial stair?

      44 in under the IBC, or 36 in where the stair serves fewer than 50 occupants. Width is measured clear between handrails at and below handrail height; handrails may project into it by the amount the code allows.

      How many exits are required?

      At least 2 exits per story for up to 500 occupants, 3 for 501 to 1,000 and 4 for more than 1,000 (IBC Table 1006.3.3). A single exit is allowed only in limited small-occupancy cases.

      How do you calculate occupant load?

      Divide the floor area by the occupant load factor for the use: 150 ft² gross per person for offices, 60 for retail, 15 ft² net for restaurants with tables and chairs, 7 for chairs only and 5 for standing space. A 12,000 ft² office floor holds 80 people.

      What if one stair is blocked?

      The IBC requires that losing any one exit leaves at least half of the required capacity. With two 44 in stairs and 60 in required, one stair alone gives 44 in, which is more than the 30 in half — so it passes.

      Sources

      1. International Building Code 2021, Chapter 10 — Means of egress (opens in a new tab)International Code Council. Occupant load factors (Table 1004.5), stairway capacity 0.3 in per occupant and the 0.2 in sprinkler + voice alarm exception (1005.3.1), egress distribution and loss of one exit (1005.5), exits per story (Table 1006.3.3), stair width 44 in or 36 in under 50 occupants (1011.2).
      2. Washington State Building Code, WAC 51-54A-1004 — Occupant loadWashington State Building Code Council. The adopted IBC Table 1004.5 occupant load factors, used to confirm the factor table.

      Code text is the final word. Editions and local amendments differ — check the edition your building department enforces.

      Stair code & structure calculatorsAll 3 tools for checking a stair — the full code check, egress stair width and stringer span.View all 3

      Other stair calculator categories